Kenwood KAC-7202 Car Audio AmplifierTroubleshooting & Support

Hot Topics:

Problems & Solutions

Solved Problems for KAC-7202 Car Audio Amplifier - White-on-White RSS Feed

I have a KAC-7202 that powers up but has no soumd

hi, if there is no indication of protect, assume the main amp is good, but check on the +12 and -12V supply on the preamp, assuming the...
- b_d_davis
- Nov 24, 2009
- 264 Views
- 1 Solution
turning down the power on my amp

Remove the top cover.
- tightend80us
- Mar 26, 2009
- 121 Views
- 2 Solutions
Kenwood KAC-7202 wont turn on

I have found the problem to my Kenwood KAC-7202. The amps fan was the only thing that would come on thats it. So I started checkin zener...
- duffman8815
- Feb 9, 2008
- 573 Views
- 2 Solutions
AMp keeps blowing fuses

http://www.howtodothings.com/electronics/how-to-fix-the-fuse-on-your-guitar-amplifier Hi You can refer to my detailed solution above...if...
- Chris Kucey
- Feb 15, 2007
- 947 Views
- 4 Solutions
brand new battery install 98 dodge pick up

A small spark when reconnecting the battery cable is normal no spark at all would be a concern sice that uaually only happens with a dead...
- anke_b
- Nov 22, 2008
- 14 Views
- 1 Solution
kenwood kac-7202 wirng 4 subs

look at the Z [impedance] specs for the amp. Look at the Z for the speakers. You may eventually have to wire them in a series-parallel...
- lonewolf74
- Oct 15, 2008
- 79 Views
- 1 Solution
Amp powers up (switchable) but has absolutely no...

If possible return the amp to the seller for a refund (before you tamper with it). If that's not possible, the amp will need to be...
- Cursedknight
- Sep 19, 2008
- 231 Views
- 2 Solutions
turns on for a second then truns off

The amp is going into a protective state.You either have a bad resistor,capacitor or coil shorting internally in the amp.If you open it up...
- crumba
- Feb 24, 2008
- 119 Views
- 2 Solutions
kac 7285 kenwood amp

Come visit us on www.sounddomain.com --- we'll help you through everything you might need to know!!!!
- morgan290103
- Jan 29, 2008
- 1338 Views
- 3 Solutions
i need to know

honestly try to buy an adapter. very easy to hook up just use the rear speaker wires as a input
- TONY SANTOYO
- Jan 19, 2008
- 38 Views
- 2 Solutions
kenwood ps 150

With your multimeter set to DC volts and the black meter lead on the ground terminal of the amp, touch the red lead alternately to the B+...
- Shawn Gagnon
- Dec 1, 2007
- 329 Views
- 1 Solution
Kenwood KAC 7502 Amp trouble

Exchange the amp it is going into Protect. But your sub may be causing this problem if it is shorted. Make sure your subs are wired to at...
- veejay Scoot
- Jun 26, 2007
- 147 Views
- 1 Solution
ampflier only pushing one speaker

the wire on the back of the sub box is not fully connected prolly so get access to the back of the sub box n adjust the positive n negative...
- Toks Opeloye
- Feb 19, 2007
- 9 Views
- 2 Solutions
Amp Trouble

Actually, it's more likely that the problem is on the outside of the amplifier than the inside. Your problem may be caused by a ground...
- Zak Garrett
- Mar 9, 2007
- 28 Views
- 1 Solution
Keep poping the 40 amp fuse on the amps itself...

Your units drawing too much current. it could be a wireing problem, a speaker problem, or the amp has a problem. the correct way to...
- Robert Whiteley
- Aug 16, 2006
- 339 Views
- 1 Solution

See all Kenwood KAC-7202 Car Audio Amplifier Solutions

Tips & How Tos

Do you have any good tips or tricks? - Write a Tip!

Unsolved Problems for KAC-7202 Car Audio Amplifier - White-on-White RSS Feed

red light only!!!

recently re-installed my 7202 kenwood. everything was working fine when disconnected from my old suburban, and when i...
- william h
- Feb 11, 2012
- 7 Views
Solve It
amplifier comes on no out put
- Mark Suiter
- Oct 3, 2011
- 7 Views
Solve It
It does not turn on

It does not turn on and doesnot provide sound
- moris_mendoz
- May 24, 2011
- 9 Views
Solve It
red light always on is that normal function or is

red light always on is that normal function or is it in protection? Also I have it set for high pass but get lots of...
- diggs7774
- Apr 21, 2011
- 17 Views
Solve It
The light is red not

The light is red not blue . How do i make it blue again
- josuesrt8
- Oct 30, 2010
- 30 Views
Solve It
red light comes on & fan is on, but no sound
- civicb16a199
- Oct 13, 2010
- 36 Views
Solve It
the fan turns on but the amp does not i have 2

the fan turns on but the amp does not i have 2 amps the same problem please help me im losing fauth in kenwood lol
- beyond_pa947
- Oct 11, 2010
- 4 Views
Solve It
My kenwood KAC-7202 wont power

My kenwood KAC-7202 wont power on from the regular rem wire from my head unit , but it will if i hook it to a bigger...
- tru_menace_5
- Oct 9, 2010
- 22 Views
Solve It
the amp powers on normal

the amp powers on normal rem wire works and the fan kicks on normally... but the amp does not play. i have checked my...
- flyboydevin
- Sep 16, 2010
- 5 Views
Solve It
My Kenwood amp picks up noise. I thought it was a

My Kenwood amp picks up noise. I thought it was a ground issue but I have re-wired my entire system directly to the...
- bigwes1988
- Aug 22, 2010
- 11 Views
Solve It