20 Most Recent
Kenwood KDC-7024 CD Player Questions & Answers
Code kenwood kdc-7024
You will need to visit an Authorized Dealer or service center for that product to get the unlock code reset. You can find a dealer listing on their website, or call them.
I dont remember my 4
The only solution now is to take it to a Radio Decoding Service (such as your local Car Radio store) where they will open up your radio and connect a laptop to read the code inside your memory chip(EEPROM) using special software.
It will not be available by any other method as KENWOOD codes are not readily available ...Sorry
My cd player keep comeing on then going off...
Check the bat + wire (RED) and the ground (Black) make sure they have good solid connection to the harness that goes into the deck. If they are electrical taped together then untaped them and krimp them together. Let me know if this solves your problem. I don't want to give you 80 solutions to one problem
Security code kdc7024
Tray this:
During code request mode,press and hold for at least 3 second TRACK UP and AUTO keys (--- will disappear).
Enter "KCAR" with the remote controlas described below:
Press the remote controller 5 key twice,and press the TRACK UP key (On the remote control) "K"
Press the remote controller 2 key three times,and press TRACK UP key "C"
Press the remote controller 2 key once,and press thr TRACK UP key "A"
Press the remote controller 7 key twice,and press TRACK UP key "R"
The security funtion is canceled and unit sets to All-Off mode
My Kenwood KDC-7024 has just
It's possible the flexible PCB (more of a cable, really) that connects the faceplate to the main unit has cracks in the conductors. This has been an issue with some of the older Kenwood HUs that have the MASK motorized faceplate. The flex-cable gets bent and pinched enough over the years that it eventually cracks the copper.
Kenwood KDC 7024
Some flip face stereos use a tiny micro switch to tell the onboard computer when the face is down or up and sometimes it uses the same switch for both positions sensing. It could be this switch is not working properly (dirty contacts, broken, bad wire, mis-aligned, etc.) and that is causing the problem. Good luck.
Security
Hi,
It is likely that your radio has been wired incorrectly, generally speaking there are two different wires that need wiring, an ignition wire, and an permanent wire, I guess you have both wired to the ignition hence when you turn off the car it forgets the code. If you check the wiring and make sure the permanent wire is connected straight to the fuse box and not the ignition it should resolve your issue.
Hope this helps
Simon
Kenwood 7024Y
during code mode,press and hold for about 3 second TRACK UP and AUTO keys (at the same time) (---- will disappear).
Enter "KCAR" with the remote control as described below:
Press 5 key twice,and pres Track up key K
Press 2 key three times,press Track Up key C
Press 2 key once,press Track Upu key A
Press 7 key twice,Press the Track up key R
Seccurity funtion is canceled and unit set to All-Off mode.
Kenwood kdc-7024
Use the am and fm buttons to increase or decrease the numbers and use the seek up button to move to the next number and then press and hold the seek button to enter the code ( these buttons are on the bottom right hand side of the fascia)
Control panel will not open when pressed in lower left corner
There are a few problems with these units including the flexible pcb's and also the detector micro switches and also the plastic gears getting sheared, I suggest you bring it back to where you had it repaired as it seems they haven't fixed it properly yet.
Unit keeps opening and shutting
Yes, in fact, I believe the ribbon cable is bad.
A new one can be ordered from www.kenwoodparts.com
Hope that helps!
Any assistance with taking the unit apart will best be found in the service manual!
Not finding what you are looking for?