RQT67077The radio: manual tuningPreparation:Press [TUNER BAND] to select “FM” or “AM”.Automatic presettingDo the following once each for FM and AM.Preparation: Tune to the frequency where pre-setting is to begin.Hold down [PROGRAM] until the frequency changes.The tuner presets all the stations it can receive into the channels inascending order. When finished, the last station memorized is tuned in.Manual presettingPre-set the stations one at a time.1 Press [PROGRAM] then press [g, REW/3] or[f,4/FF] to tune to the desired station.2 Press [PROGRAM] then press [g, REW/3] or[f,4/FF] to select a channel.3 Press [PROGRAM].The station occupying a channel is erased if another station is presetin that channel.Selecting channelsPress the numbered buttons to select the channel.To enter channel 10 or over, press [X10], then the two digits.OR1 Press [PLAY MODE] to select “PRESET”.2 Press [g, REW/3] or [f, 4/FF] to select thechannel.The radio: preset tuningRemotecontrolonlyThere are two methods of pre-setting stations.Automatic presetting : All the stations the tuner can receive arepreset.Manual presetting: You can select the stations to preset and theorder they are preset in.Up to 15 stations each can be set in the FM and AM bands.1 Press [TUNER/BAND] to select band.The unit comes on.Every time you press the button:FM AM2 Press [PLAY MODE] on the remote control to select“MANUAL”.Every time you press the button:MANUAL PRESET3 Hold down [g/REW/3] or [f/FF/4] for a momentto search for a station.The frequency stops when it finds a clear station.To stop during the process, press[g/REW/3] or[f/FF/4].Under excessive interference, a station may not be found.Press[g/REW/3] or[f/FF/4] repeatedly to tune step-by-step.“TUNED” is displayed when a radio station is tuned.“ST” is displayed when a stereo FM broadcast is beingreceived.IfnoiseisexcessiveinFMRemote control onlyHold down [PLAY MODE] to display “MONO”.Monaural sound is selected and noise reduces when reception isweak.Hold down [PLAY MODE] again to cancel the mode.“MONO” is also cancelled if the frequency is changed.To receive FM broadcasts allocated in 0.1 MHz stepsMain unit onlyHold down [TUNER/BAND]. The display changes in a few seconds toshow the current minimum FM frequency. Continue to hold down thebutton until the minimum frequency changes. The step is changed.Repeat the above to change the step back.Note• After changing the “allocation” setting, the frequencies you previouslypreset in the memory will be cleared.• Sound is momentarily interrupted if you load/unload tapes whilelistening to an AM broadcast.VOLVOLVOLVOL7890106SHISHIFTCLOCKCLOCKTIMERTIMER//PLPL AYRECRECAUT OFFO OFFINTROINTROS.SOSOUND EQUNDEQ PRERESE EQT EQ MUTUTINGINGENTERENTERMARKERMARKERTITLETITLESEARCHSEARCHREWFFPROGPROGRAMAMREPREPEATATPLAY MODEAYMODEDISCDISCSPACESPACEABCABCDEFDEFGHIGHITUVTUVWXYZPQRSPQRSJKLJKLMNOMNOSLEEPEEPCD DISPCD DISPDIMMERDIMMERALBUMBUMCURSORCURSORDELDEL45123TAPETAPECDCDAUXAUXCLEARLEARTUNERTUNERBANDNDWOOFERS.WOOFERVOLVOLVOLVOL7 8 90106SHISHIFTCLOCKCLOCKTIMERTIMER//PLPL AYRECRECAUTOFFO OFFINTROINTROS.SOSOUND EQUNDEQ PRERESEEQT EQ MUTUTINGINGENTERENTERMARKERMARKERTITLETITLESEARCHSEARCHREWFFPROGPROGRAMAMREPREPEATATPLAY MODEAYMODEDISCDISCSPACESPACEABCABCDEFDEFGHIGHITUVTUVWXY ZPQRSPQRSJKLJKLMNOMNOSLEEPEEPCD DISPCDDISPDIMMERDIMMERALBUMBUMCURSORCURSORDELDEL45123TAPETAPECDCDAUXAUXCLEARLEARTUNERTUNERBANDNDWOOFERS.WOOFER
Guru