20 Most Recent
Sony KDF-E55A20 55 in. LCD Television - Page 7 Questions & Answers
My tv doesn't work, lamp
Replacing the Lamp should fix the problem. The Lamp door is located on the lower right side.
Remove the door, there should be a inner door that has a oblong knob, turn it counter clock-wise. the door should come out, the Lamp has a loop lever, pull up on the lever and remove the lamp. Most of the time it is shattered. The new lamp is installed in reverse order.
I believe the Lamp number is XL-2100U. But to make sure, check the owners manuel.
If you cannot find one local to you, you can order one through Sony at 1800-222-sony. All you will need is the model number. It should run around 185.00.
I hope this helps,
Skyassoc
Blue dots all over screen
You
need an optical block. PN: A-1132-202-A. Part is very expensive with a $1500
core charge. Consider replacing the TV. Sorry, this is will eventually happen to
all Rear Projection LCD televisions. The UV light emitted from the projection
lamp destroys the Blue LCD panel first (shorter wave length), then the Green
then the Red. The panels are not serviceable, the entire unit must be changed. I
hope this helps... it will save you a $100+ service call fee anyway.
My screen/picture is getting darker and darker and
Hello.
You have to stop watching your TV like this before you damage ballast and replace lamp that according specifications have to be replaced every 2.5 years of average use.
I recommend buy original lamp fully assembled. Info on how to replace it is in your owner's manual.
Regards.
Russ.
Will shut off for about
The "LAMP" LED light indication flashes or staying on?Yes,than Lamp life are over.Tv require a new Lamp.
Tv keeps turning off and on
This happens due to weak lamp in tv that has reached to end of working hours life, replace lamp in tv to fix this issue.
Lamp replacement procedure is easy and would be written in user manual.
Thanks.
I have a Sony KDF-E55A20. I just replaced the
Put lamp cover back on tv as it will push a safety switch inside then tv will turn On.
Lamp cover is first thing that you removed to replace lamp in tv.
Hope this will help you.
Thanks.
Replaced xl-2200 bulb still red
Look at the output transformers in the high voltagesection of your TV very closely. These transformers have been known to fail sometimes if you look closely you can see the burnt places on the circuit board under the bad transformer. These transformers cost about $30.00. This will fix your TV.
My Sony Grand Wega KDF-E55A20
6 times is the lamp thermal fuse or lamp. its a thermal that sits on the bottom of the lamp area.
remove the fan and you will see the siler disk with black base cut the wires and slide the new one in on the side secure it on the old thermal and your fixed.
My TV keeps turning off
It is weak lamp in tv that has reached at an end of its working life yet not broken/ dead and causing this problem.
If lamp has not been replaced in tv in last 2-3 years, then replace it to fix tv issue.
Lamp replacement procedure is easy and written in user manual.
Thanks.
MY SONY KDF E 55A20 REAR PROJECTION TV HAS THIN
You need to replace the optical block to fix this problem it sounds like one of your LCD chips is burning out and that is why you get this kind of side effect the OPTICAL BLOCK usually runs around $230.00 - $350.00dls plus labor here is a guide if you want to replace it on your own
http://sites.google.com/site/sonylcdrptvproblems/sonykdf-55wf655opticalblockreplacement
PLEASE RATE THIS SOLUTION AS I DO THIS FOR FREE !!!!
About 2-3 times per
Hi,
Sounds lamp is near to end of working life and weak lamp can cause that symptom, broken lamp will lit lamp light on tv front but weak lamp wont lit that light but tv lose picture for little time.
Replace lamp in tv to fix its issue. Lamp replacement procedure would written in user manual copy.
Thanks.
Hello our sony grand wega KDF e55a20 has the green
Hi,
Symptom shows Lamp is not working and either lamp or its drive board is bad that will be replaced.
Did you replaced lamp in tv recently?
If not, replace it. Lamp replacement procedure would be written in user manual.
Thanks.
Not finding what you are looking for?