Philips 60PP9352 60" Rear Projection Television - Answered Questions & Fixed issues


it may be that the dish alignment needs resetting or the lnb is going bad

Philips 60PP9352... | Answered on Feb 15, 2018 | 204 views


Fault to the main power supply regulator section. Either it will be a separate board, or the part of main board. Check and replace damaged component/s at its main power regulator [SMPS] section circuit. Contact any service technician. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/

Philips 60PP9352... | Answered on May 17, 2016 | 36 views


you might need a new bulb, bulbs average around 4000 hours, depending on the bulb, they range from 750-6000 hours

Philips 60PP9352... | Answered on Apr 22, 2014 | 59 views


I replaced bulb but still no picture

Philips 60PP9352... | Answered on Dec 25, 2012 | 89 views


the set uses two stk-392-120 convergence chips, both will need to be replaced and the set adjusted--tvrepair.com sells kits for this based on brand and model number.


10_26_2012_6_41_04_pm.jpg

Philips 60PP9352... | Answered on Oct 26, 2012 | 65 views


Problem is in standby power supply or microprocessor area---not the do it yourself repair and likely not economical to repair due to age and brand of set.

Philips 60PP9352... | Answered on Sep 01, 2012 | 70 views


All CRT RPTVs have overscan, and some sources bring this out more than others.

It can always be cured to at least be able to see the needed parts of the pic, but hoses your picture beyond belief, and correcting that takes time, experience, patience and expertise.

I do overscan reduction on all CRT RPTVs as part of what my calibrations offer, but charge extra to do so.

Mr Bob

Philips 60PP9352... | Answered on Jan 31, 2012 | 181 views


impossible to find in most cases...check with www.TvRepairKits.com - they may have a used one forsale

Philips 60PP9352... | Answered on Sep 29, 2011 | 273 views


You cant. You will need the remote control to control the adjustments. You can get the remote for your model from www.tvrepairworld.com

Philips 60PP9352... | Answered on Aug 24, 2011 | 56 views


The CRT coolant change is all mechanical which involves removing the crt and disassembling the coolant chamber so it can be cleaned then reassembled and filled with coolant the phillips CRT coolant kit from www.tvrepairworld.com has the coolant and the instructions for the repair on cd

Philips 60PP9352... | Answered on Jul 31, 2011 | 330 views


dont waiste your money problem main or logic board or if shure power supply go radio shack and get one with specifications match voltage,ampers,and polarity

Philips 60PP9352... | Answered on Jun 06, 2011 | 5,066 views


If the images are getting darker then its certainly an issue with the three CRT tubes that are dying. Slowly the images will get darker and darker till you can no longer see a pic. If the image level is viewable then a brigthness/contrast adjustment should resolve the problem atleast for now. Otherwise you will need to replace the three CRT tubes to resolve this problem. This being a high voltage repair its recommended that you seek the assistance of a qualified tech as we are dealing with 30,000V here. As my mentor always says your life and limb are worth much more than this

Philips 60PP9352... | Answered on Mar 25, 2011 | 27 views


Most likely your bulb has burned out. Best replacements come from the OEM, and are fairly easy to change.

Philips 60PP9352... | Answered on Feb 28, 2011 | 17 views


If your TV looks 3D, warped, or distorted it likely has a convergenge problem.
If however it just looks dull, washed out, redish, or if it looks like objects on the screen have halos the fluid in the lens has soured.
You can search google for parts or you can get the parts with repair instructions from sites such as www.TvRepairKits.com

Philips 60PP9352... | Answered on Feb 25, 2011 | 35 views


If your talikng about alignment that is done through the Convergence feature. If its the color balance youre refering too its most likley indicating that the CRT coolant needs replacment as that will make the red Tube dominate and wash out both blue and green colors untill they appear dull and dim.

Philips 60PP9352... | Answered on Feb 18, 2011 | 47 views


If colors are skewed or look 3 d the convergence chips need to be replaced. This model should use two of the STK-392-120 BUT A FEW VERSIONS USE STK-392-110.

THE CHIPS ARE BLACK--2 1/2 INCH WIDE & 1 1/2 TALL WITH 18 PINS EACH.

They are located on the large left board as you look from the back on metal heat sinks with fins. This can be a do it yourself repair if you have some skill.

Look at the chips if you remove the back cover; look at all the tiny resistors around the one close to the front of the set, most are 1.2 ohm 1/2 watt---you are looking for any that are white in the middle or discolored.

Usual cost on EBAY for a pair of the chips is under 14 dollars and the resistors are easy to test.

I can tell you the best way to get at them and do the repair.

If you want to save the set and save money I can help you.

My knowledge is first hand---I have repaired over 1,000 sets with this kind of problem.

Let me know what you want to do and I will assist you from start to finish.

If this information is helpful rate this solution as "very helpful" as I do this here for free.

REGARDS, SD TECH

Philips 60PP9352... | Answered on Feb 17, 2011 | 422 views


That sounds to me like weak tubes or low emmission tubes. If it is old, it may be past its best and time for a new one.

Philips 60PP9352... | Answered on Feb 06, 2011 | 29 views


In most cases the HVG - Flyback has gone out on this model. We see this alot. The problem is they are very hard to find.

Philips 60PP9352... | Answered on Jan 30, 2011 | 40 views


The burned smell comes from a shorted parts.
This is usually a burned fusible resistor act as a guard when there is a short circiut to avoid further damaged to other parts. I've suspect that you have a short on the power supply section which is caused by voltage regulator. This is not DIY and quite technical so I've advice you to look for a qualified technician or repair shop to isolate the problem. This is fixable.

Thanks for using fixya.

Please rate my help.

Philips 60PP9352... | Answered on Jan 24, 2011 | 59 views


Sounds like you have a capacitor going out on the same chipboard!! While your inside of the LCD's it would not hurt to fix the other capacitors. Normally when a capacitor goes out, the same resistors on the same chip group need to be changed as well. If they are not changed, it may cause the same capacitors to go out after a few hours of use. Ensure to check your display cable connection and yes, please connect it to a pc. You may get a blank, light blue, or other light display but not really enough to determine if the problem has been completely fixed.
Certified TV EXPERT

Philips 60PP9352... | Answered on Jan 23, 2011 | 18 views

Not finding what you are looking for?
Philips 60PP9352 60" Rear Projection Television Logo

182 questions posted

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76054 Answers

matt martin
matt martin

Level 3 Expert

1255 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...