Westinghouse LTV-27W2 27 in. HD-Ready LCD Television - Answered Questions & Fixed issues


Sounds like T'Con board fault. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/
Screen-shots to defective LCD panels are given. You can see and compare to that to your TVs', and can make sure about the fault to an extent.

Westinghouse... | Answered on Oct 09, 2015 | 42 views


I sent my question to the "solve your problem for free" on this website, so I was expecting some "free" advice. My finances are such that I can only ask for free advice. I did see someone who had a similar-sounding problem, and there was a mention of two possible main boards that would fix the problem. I was hoping to know which board would most likely fix my problem, since the TV is less than two years old. If I take it to a TV repair person, I want to have a fairly good idea how to fix it, and what would be the approximate cost, so I do not get ripped off.

Westinghouse... | Answered on May 20, 2014 | 323 views


It is a little difficult to be certain where the problem is with that description, but at least statistically it is more likely to be in the power board than the main board.

You can send it for repair to us or you can search for a replacement, they go about $70-$80.

Westinghouse... | Answered on Oct 30, 2012 | 190 views


That could be either the Power supply or the main board. I would think the main board is most likely because of the Blue screen you mentioned.

Westinghouse... | Answered on Oct 30, 2012 | 525 views


Codes listed in my manual for White Westinghouse are 0169 or 0003 or 0014 or 0043. Are yousure though there isn't a flip down panel somewhere which gives you the option to access "enter"

Westinghouse... | Answered on Oct 15, 2012 | 1,818 views


Improper color reproduction is the problem. Normally this type of problems to LCD TVs will be due to the fault to its T'Con board. But, before make it sure, re-seat all the flat cable connections that goes to LCD panel from this board.

Westinghouse... | Answered on Jul 10, 2012 | 310 views


what are you using for signal and how are you connected? Tried a DVD or Blue Ray to see if that does the same things or not?

Westinghouse... | Answered on Apr 08, 2012 | 163 views


Bad capicitors in power supply just fixed it in my tv

Westinghouse... | Answered on Jan 05, 2012 | 533 views


which product..??

Westinghouse... | Answered on Jan 02, 2012 | 28 views


I have had this problem before and found a loose connection on the power supply module on C310 next to T1 transformer. If you have soldered before you should have on problem. Just take the back off the set and the power module is the one that has the AC cord hookup. Search for C310 and remove the module via screws and unplug it and turn it upside down to the solder side of the board at the C310 location looking for the loose connection there. If you can't see it then solder it anyway and try turning the set back on after putting the board back plugged up and all. Use electronic rosin core solder and a good soldering iron that will get hot enough to do the job. If this is not the problem then suspect an open T3 in the inverter circuit. This is a transformer. T3 may be available by calling Westinghouse by looking on the internet for the manufacturer. Changing it will require using solder wick to remove the transformer and clean the holes to put in a new on. Otherwise if you cannot get T3 the whole board would need to be replaced via manufacturer or try to find on on Ebay doing a search with the model number. Also try Shop Jimmy .com or just a google search

Westinghouse... | Answered on Oct 23, 2011 | 37 views


Go to
http://rcaaudiovideo.com/
On the left side select 'remotes' and then your remote type. You will be able to download the manual and codes for your RCA Remote Control.
Let me know if you have any other questions. Please rate this solution. Thanks.

Westinghouse... | Answered on Jul 23, 2011 | 729 views


Hi my first guess is the power supply. You can inpect it for bulged capacitors that might be obvious. My second thought is the signal board but I leaning more towards the power supply. If you want to buy parts you can find them at www.interliquidparts.com in order to get parts you have to get the part numbers from the actual part on your TV. If you open it up it has a part number stamped to it. Be carefull opening up the TV it has high voltage. leave it unplugged for a couple of hours before opening it up.

Westinghouse... | Answered on Jun 02, 2011 | 116 views


Good day,

It's the problem of overheating in the power supply board of the TV.on the power supply board of the TV there are few capacitors and IC.any of this IC is got short or may be weak.so due to this when you start the TV the current passes from electric outlet to the power supply board of TV.but when the current passes from that weak/faulty part at that time current gets stopped or slow and the board overheats and TV shuts off. this is a common problem faced by many other users too.the possible option to solve this issue is to check the power supply board by a meter and continuity tester and replace the faulty component on the board which is short due to which power supply board is getting overheated.its bit technical job but yes its not at all a costly repair to do or get it done by the technician. for required parts it can be easily available from local electronic shop.

I hope this help to rectify the problem and take caution in handling the television, because it's fragile and contains high voltages....

Westinghouse... | Answered on May 13, 2011 | 1,628 views


Most likely, a number of capacitors need to be replaced in the power supply on this set, OR possibly, there is a bad connection on a connection on the snubber capacitor in the power supply, near the SMT transformer--and I have seen this MANY times on westinghouse LCD sets. .

Westinghouse... | Answered on Apr 11, 2011 | 1,154 views


These sets have a problem with the backlight circuitry which causes the set to operate properly( tune channels, sound ok, etc..) but there is no picture..this is likely caused by the filter capacitors in the inverter power supply circuit which , over time, tend to either leak or lose thier esr value. The repair usually consists of replacing a few electrolytic capacitors and possibly a resistor or fuse. If you can find someone who repairs these near you, you may want to get an estimate...theoretically, the components are not very expensive for this repair., and takes little time..so look out for scammers

Westinghouse... | Answered on Mar 26, 2011 | 289 views


Tv turn on now.Dispaly go out about 8 mins,but does it still have audio?Yes,than the tv 1 or 2 long board call the LCD inverter boards are dead.These 1 or 2 long inverter boards help the tv to have backlight to produce a picture.Tries websites like Shopjimmy.com,Ebay.com to buy those 1 or 2 long refurbishes inverter boards for the replacement.

Westinghouse... | Answered on Dec 09, 2010 | 101 views


check the energy saver settings

Westinghouse... | Answered on Oct 13, 2010 | 338 views


Hello, this symptom is normally caused by several things. The most common one is the T-Con board. This can be caused by over heating in the unit which will cause the T-Con board to go bad. Once this board is replaced it should all be okay. For more information on getting this problem fixed as well as live troubleshooting, please email me at westytech@westinghousedigital.com

Westinghouse... | Answered on Oct 05, 2010 | 63 views


It may have cold solder joints, loose connections, etc. You need to take voltage readings before and after the problem occurs.
If you are going to DIY and have proper tools, electronics knowledge, and know safety precaution then please read on:

Please see my basic troubleshooting guide here:
http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide

Failed TV and Monitors: http://s807.photobucket.com/home/budm/allalbums

http://en.wikipedia.org/wiki/Capacitor_plague

Parts: www.shopjimmy.com
Capacitors kit: http://lcdalternatives.auctivacommerce.com/Default.aspx he can make you a set of caps.

Westinghouse... | Answered on Sep 30, 2010 | 55 views


There is no reset button, to reset it, unplug it for about an hour to let it reset itself.
Are you having problem with the set?

http://www.fixya.com/support/r5093881-lcd_flat_panel_tv_troubleshooting_guide

Failed TV and Monitors: http://s807.photobucket.com/home/budm/allalbums

http://en.wikipedia.org/wiki/Capacitor_plague

Westinghouse... | Answered on Sep 01, 2010 | 307 views

Not finding what you are looking for?
Westinghouse LTV-27W2 27 in. HD-Ready LCD Television Logo

95 questions posted

Ask a Question

Usually answered in minutes!

Top Westinghouse Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76099 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Westinghouse Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...