20 Most Recent
Bush DVD142RC 14 in. TV/DVD Combo - Page 5 Questions & Answers
DVD1402TVP
Buy one cdclener and insertion your DVD tray agay now
Dvd txa2028
could be that the tray is not fully loading it or the spinal is down more that it should or laser is bad, have to take it in for repair.
Get my dvd out
most likely you will need to pull off the left side of the case if it's a tower case, otherwise for a dektop case you will need to lift the top off, and make sure that the power cable is pluged in the back of the cd player properly , its the white plug your looking for , but if the light is flashing on the front of the cd player , that means there is no need to check that the cable is in, so in this case the eject drive is most likely jammed, so while u press the eject button try pulling it the front of the eject door ,
No picture from video
CLEANING THE VIDEO HEADS - in the event of a head clog, the first thing professionals try to accomplish on a cleaning job is to restore the picture. Cleaning the video heads is the most critical part of the process. Use extreme caution. Never use cotton swabs. Cotton tends to grab, get caught or leave fibers in the heads. It can also break them. Using chamois sticks is by far the safest method.
Soak a chamois stick with head cleaning fluid and place it directly on a video head with light pressure. For beginners, the safest method involves holding the chamois stick stationary in one hand and rotating the drum clockwise with the other. You want all scrubbing action to be in a horizontal direction. Never use any vertical motion; it's very risky for head tip breakage. When finished, allow a minute or two for the heads to dry and your ready to try it out.
Pop in a tape and press PLAY. Confirm the picture is now clear. If not, you might want to repeat the above process once again. Ninety eight percent of the time, cleaning the video heads solves this symptom. Most of the remaining two percent is caused by a defective video head somewhere on the upper drum. Hope this helps
Ps Dont forget to rate this.
Parts for this off brand
I searched and search all over to no avail. What I suggested for this once before BUT im not sure where it went was to look inside the ouwners manual to find out who to contact for this model as I cant find it. Also what you can do is pull out the tuner assy clean it up from excessive solder and send to PTS and maybe they can rebuild the tuner for you. Also seek advise from who ever sells this product in your area for a # they would contact if they the store needed service. Im sorry I coulnt assist you more in this matter. Go to http://www.ptscorp.com to see where to send the tuner or a contact #. Good Luck
14" Tv/vid combi
If the light blinks it indicates a fault, probably in the high voltage circuit. If it is steady the problem could be anywhere. First you need to check all internal fuses. Then power supply for all necessary voltages. If this checks out each section would have to be isolated. At this point a service manual would be helpful (www.servicemanuals.net). From there it would be a matter of a process of elimination. Everything I said is contingent upon you being familiar with and capable of doing the work. These things are dangerous and best left to professioals if you are not trained. Good luck.
Blue missing from picture, ie red and green only visible
You could have a bad connection on the picture tube socket, the Driver transistor could be bad or a poor solder connectionm in the blue driver circuit or the picture tube could be bad. Now there are no user serviceable parts inside this set so you shouldnt be looking or tinkering with it unless you know the HI voltage concerns involved with serviceing tv sets. you should be able to get an estimate on this set at your local repair shop, Good Luck
Bush Smart Television. Lost WiFi on it?
Question edited for clarity.
Question moved from Smart Computers to Bush Television.
No, if is worked before, you don't need a booster. It is a software glitch or a WiFi setting that is incorrect.
Factory Reset the television. Re-enter the WiFi settings, (SSID and Password), and then do any Software Updates.
Google
bush (model) factory reset
All questions need 'make model (what is is)' as first 3 words please.
..
Not finding what you are looking for?