Toshiba 57H82 57" Rear Projection Television - Answered Questions & Fixed issues


For a service manual, contact Toshiba directly.

Toshiba 57H82... | Answered on Jun 17, 2017 | 58 views


the hdmi is a hdcp circuitry meanining it handles high-bandwith digital content protection hence the hdcp its a security copy device that protects a device from intercepting digital data, this error code means its corrupted and needs to be reprogrammed digitally u will need an computer tech conversant with computer digital electronics

Toshiba 57H82... | Answered on Jul 14, 2013 | 69 views


57H82 does not have a color wheel but 3 picture tubes, remove rear cover and look for the three large black lens--if dusty they will lower brightness and make the set look dull or washed out.

Toshiba 57H82... | Answered on Dec 06, 2012 | 49 views


I have a possible answer---are you getting noise lines across the screen for the first several minutes that would eventually clear up and give a picture or something else?

Toshiba 57H82... | Answered on Dec 03, 2012 | 77 views


I doubt the model as old as it is will work without a converter.

Toshiba 57H82... | Answered on Oct 26, 2012 | 120 views


This set is prone to only two real issues--one is the Hyper board which will not cause this issue.

The other issue is convergence---only way to prove if it is your problem is to gain access to the two STK-392-110 (SHOULD USE THAT) AND unsolder all pins on both--each has 18 pins.

With them out of the circuit if set comes on (will look bad) one of the chips is shorted--they are also protected by pico fuses--and you will have the same problem if one of the special fuses are bad.

There are two of these fuse devices (not a glass fuse) for the convergence and they usually are 5 amp. I would look for the fuses first and if either is bad both chips have to be replaced at same time.

Toshiba 57H82... | Answered on May 29, 2012 | 27 views


Take a look at this video to see if your a a true convergence problem or just need an adjustment.

Toshiba 57H82... | Answered on May 11, 2012 | 86 views


This may be a convergence issue but it is difficult to determine with that description. Watch this video and see if it will help you determine if you have a convergence problem or possible something else.

Toshiba 57H82... | Answered on Apr 17, 2012 | 170 views


Typically this is due to a convergence chip failure. This repair can be done pretty easy with the proper instruction. Have a look at this video to help determine if you truly have a convergence problem.

Toshiba 57H82... | Answered on Apr 17, 2012 | 979 views


It uses 3 picture tubes that rarely fail--Let me know what is wrong--most common issue is convergence--often mistaken for a bad tube.

See some attached photos to see if they look like your problem.


4_7_2012_4_14_52_pm.jpg


4_7_2012_4_17_04_pm.jpg



4_7_2012_4_18_21_pm.jpg


No two sets will look exactly the same with this problem but from the photos you should know if this is your problem or not.

Toshiba 57H82... | Answered on Apr 10, 2012 | 28 views


You should be able to order this from a company called MCM electroincs on line.

Toshiba 57H82... | Answered on Feb 02, 2012 | 29 views


Check for solder bridge along the convergence ic's. Check low value resistors in the circuit. Make sure you have your +27 and -27 vcc going to the ic's.

Toshiba 57H82... | Answered on Nov 21, 2011 | 53 views


HAD ONE ALMOST LIKE IT 62 INCH DLP LIGHT ENGINE DRIVE WENT OUT THEY DO NOT MANUFACTER IT ANY MORE WARRENTY COMPANY FEED ME A 60 INCH MITSUBISHI THERE IS NO HELP WHEN THE LIGHTENGINE DRIVE GOES OUT CASH IT IN!?

Toshiba 57H82... | Answered on Aug 30, 2011 | 69 views


1)Make sure the ventilation slots are clear of dust and debris.
2)listen for odd sounds from within the housing. snaps,crackles and pops are not good sounds.
3)Make sure the fans are running
4)Remove the lamp,following the instructions in your manual. Do not touch any part of the glass lamp!!!!!!!
One sign of a bad lamp is a blackened base of the arc chamber(the tube inside the lamp.)
There is really no way to test arc lamps except send it to the mfr.

Good luck! let me know if you figure it out.

Toshiba 57H82... | Answered on Aug 30, 2011 | 55 views


The cause of that problem is the CRT socket.Try to replace the crt socket because if that socket deffect it may cause of picture delay.

Toshiba 57H82... | Answered on Jul 05, 2011 | 38 views


Some of your electronics parts were worn out. Like capacitors may have leaks that need to be replace
as use stated that the word focus were very clear it means that your tube is still okay. or you adjust the focus knob on the compartment. To tune in the 3 colors.

Toshiba 57H82... | Answered on Jun 10, 2011 | 218 views


Your hypermodule has gone out and will need to be repaired. You can google for the capacitor locations - I beleive its 11 of them. This is a tricky repair since the caps are small. If you do it yourself I would advise using small cam corder capacitors instead of the SMD type that installed. This will make it easier to replace. You can also get a complete kit with instructions from www.TvRepairKits.com or similar sites.

Toshiba 57H82... | Answered on May 12, 2011 | 35 views


If the TV looks zig zag or scrambled and its moving aroudn the screen the hypermodule has failed.
If however it looks 3D or warped and is not moving around the convergence is the issue. You can get DIY repair kits including all parts, instructions, and support from sites such as www.TvRepairKits.com

Toshiba 57H82... | Answered on May 01, 2011 | 91 views


Projection TV sets have two very common problems. One is convergence ( 3D/Warped video) the other is CRT fluid ( Dull Video). Here are more details and solutions for both. Repair kits with instructions are also avail from www.TvRepairKits.com

Common Problem #1) Convergence has gone out

Projection TV sets need to have all three colors - RED - BLUE - GREEN - lined up correctly on the screen in order for the video to look normal. When its out of alignment the video will look 3D, wavy, distorted, etc. Most of the time you just need to adjust your convergence in the TV menu. If you cannot adjust it in the menu - then your convergence is broken and needs to be repaired.

This is a very common failure on these projection sets and a fairly simple DIY fix. All projection sets including Samsung, RCA, Sony, Philip Magnavox, Panasonic, Pioneer, Akai, GE, JVC, Toshiba, and others at some point will have the same problem.

Common Symptoms include....

  • Screen looks 3D
  • Colors don't line up
  • One or more colors can't be adjusted when using the convergence menu.
  • Screen is bowed or warped.
  • TV shuts off after powering on. Power light will blink. TV may also make a chirping noise.
Here are some pics of convergence problems.


7859b01.jpg

e87380c.jpg
69189a5.pngSOLUTION #1

For more more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Common Problem #2) CRT Fluid is Cloudy

Projection TV tubes have a liquid coolant that is used to keep them from overheating. After many years the coolant in the blue and green tubes will become cloudy and cause the screen to look dull, red/orange, etc. You may even see halos around images.

Picture of a set that needs the fluid changed.

578ba6c.jpg
TV set after fluid change

65af323.jpg

69189a5.pngSOLUTION

You can see some more examples and find a fix using this link on Fixya http://www.fixya.com/support/r2861467-solution_video_looking_whiteish_dull

Toshiba 57H82... | Answered on Apr 22, 2011 | 109 views

Not finding what you are looking for?
Toshiba 57H82 57" Rear Projection Television Logo

230 questions posted

Ask a Question

Usually answered in minutes!

Top Toshiba Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76099 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Toshiba Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...