20 Most Recent Apex Digital AT2702 27" TV - Page 7 Questions & Answers


unplug the tv and the direct cable box reset the box by plugging both the tv and box back in. MAKE SURE the tv is set on the right input for the box first. if the tv said to do auto scan then you lost the connection from the box either by changing the input that box is connected to if by a cable its usually 3 or 4. if by hdmi or rca cables its an input channel. also make sure not cables are loose try that first before unplugging the tv let me know

Apex Digital... | Answered on Dec 03, 2016


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary.
Before going further; try a hard reset first. If it does not help you, replace the main digital board. There are two methods to reset TVs. The first is simple to do; a Hard Reset. The other is somewhat skilled; is a Factory Reset (System Reset). To make it a hard reset, just unplug the TV from AC mains wall socket, and re-plug it back after 15 minutes or so. If you do this by overnight is better. This procedure will make it a hard reset. If you want to make it a system reset [Factory Reset]; you have to enter its service mode option, and select the factory reset option. If you wish to get some details; visit the site linked here.

Apex Digital... | Answered on Nov 12, 2016


The general set-up codes for Apex brand TVs are: 0036 0037
0038 0039
Set-up (Programming) procedure is too much to type in here, and is not practical and it will differ brand-to-brand remote controls. If you wish to get more; check the sites linked here. The site has set-up code list & set-up procedure to many popular brand remote controls. The site has general set-up codes to check with TVs and other devices are given, in the order of the 'device's brand name list' in alphabetical order. Set-up code list to many brand remote controls also is given. Pull up older posts. Search the sites by type in the brand name to your device in its search box at the top right part of the display window. It will help you to find the document easily.
http://remotesearch.blogspot.com/
http://electronicshelponline.blogspot.com/
http://electrohelponline.blogspot.com/
Programming Notes
• If your device does not respond to the remote after trying all codes listed or your brand is not listed in the code list, use the Auto Code Search method to program your remote.
• Sometimes the first code that "works" with your device may operate only a few functions of your device. There may be another code in the code list that performs more functions. Try other codes from the code list for more functionality.
This is a trial and error procedure; and quiet time consuming. You might have to check different codes said for your device.
Search the site by type in the "brand name" to your device; in the "Search box at the top right of the display window" to get gathered related posts.

Apex Digital... | Answered on Oct 24, 2016


Fault at its main digital board. Short circuited component/s at it. Contact any service technician; or the authorized service center. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. http://electronicshelponline.blogspot.com/ In most cases, the main board might have to be replaced. If so, a software [firmware] update too might be necessary..

Apex Digital... | Answered on Oct 08, 2016


If you can get into the menu with the buttons do a channel search with whatever your source is turned on. Hopefully it will catch it. If not you will need to buy a cheap little remote ($5 or so)

Apex Digital... | Answered on Sep 01, 2016


On the rear

Apex Digital... | Answered on Aug 24, 2016


Code, if applicable, will be in the remote. If your Apex remote is compatible with your Apex player, you should be able to control it directly just by pressing DVD and the power button.

Apex Digital... | Answered on Aug 21, 2016


not all sets have the capability, not all programmes have captions.

This tell you how to turn OFF, but just choose ON.
http://captionmax.com/resources/turn-off-captions/

and I found this

Best Answer: There are two types of closed captions; analog and digital. It's possible that you turned one off and not the other. Some sets will only allow you to access the menus for the type of signal you are watching so make sure you are tuned to the offending channel when you access the menus.

Also, you might want to check other devices that the signal may go through on it's way to the TV like cable boxes and DVD players. Sometimes those have closed caption decoders, too.
Source(s): Broadcast Engineer for 30+ years.





Captioning Services Turn Off Closed Captions

Apex Digital... | Answered on Jun 12, 2016


Check and replace damaged component/s at its horizontal scan output section circuit. Check the LOT (Line Output Transformer) too for damage. Replace the horizontal scan output transistor. Check the input voltage to LOT. If the voltage is absent check the feeder resistor; if any. If you wish to get some details; check the site linked here. Pull up older posts.
http://electronicshelponline.blogspot.com/
Type in this key phrase " my service table today " in the search box at the top right of the display window of the home page, to get gathered some pages which has the details of practical experiences to the author of that site.

Apex Digital... | Answered on May 09, 2016


T'Con board fault. If you wish to get some details; check the site linked here. Pull up older posts.
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
Faults & possible causes to LCD screen are given with illustrations. You can get an idea about the fault to an extent. Faults to all LCD screen are similar, irrespective of its brand and screen size.

Apex Digital... | Answered on Apr 19, 2016


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electro-medical.blogspot.com/
http://electronicshelponline.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced. To some models of sets, all these section circuit will be integrated at its main board. If this is the case, you have to replace the main board.

Apex Digital... | Answered on Mar 31, 2016


Some DVR's do not send audio via HDMI. Mine doesn't. I have to run audio cables from the DVR to the TV.

Also, check on the TV settings to try alternate audio inputs.

Apex Digital... | Answered on Mar 20, 2016


This is most likely caused by a bad inverter on the back light.

Apex Digital... | Answered on Feb 06, 2016


  • Turn everything off. Turn on TV and Select dvd input (Source). Wait 10 or so seconds. Turn on DVD player. Works for me with similar problem. Good luck -
  • John

Apex Digital... | Answered on Jan 17, 2016


Back - light problem. Check and replace damaged component/s at its back-light inverter board, or replace this board as card basis. If you wish to get some details; check the site linked here. Surf the site with patience. Pull up older posts. It will be best to replace the inverter board as card basis.
http://electro-medical.blogspot.com/
To some model sets; especially LED back-lighted types; the back-light inverter circuit will be part of the main power supply board [SMPS]. In such cases, the power supply board might need replacement. To some models sets, the back-light inverter and SMPS section circuit will be integrated at its main board itself. If so; the main board should be replaced.

Apex Digital... | Answered on Jan 09, 2016

Not finding what you are looking for?
Apex Digital AT2702 27" TV Logo

120 questions posted

Ask a Question

Usually answered in minutes!

Top Apex Digital Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76060 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you an Apex Digital Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Apex Digital Televison & Video

  • Apex Digital Televison & Video

Most Popular Question

need unjversal remote

  • Televison & Video
Loading...