Top 20 Hitachi 61SWX10B 61" Rear Projection Television Questions & Answers


Check the speaker/s. If found OK; check and replace the damaged component/s at its audio output section circuit board. If needy, replace this board as card basis. If you wish to get some details; check the site linked here. Pull up older posts. Search the site by type in the "brand name" to your device; in the "Search box at the top right of the display window of the Homepage" to get gathered related posts. http://electronicshelponline.blogspot.com/

Hitachi 61SWX10B... | 280 views | 0 helpful votes


Hi Ellie!

Maybe in the manual you can find any information how to resolve this problem.

On this page of the manual there are shown most common receprion problems: http://manualsbrain.com/ru/manuals/979781/?page=72

Hitachi 61SWX10B... | 257 views | 0 helpful votes


Double picture (ghosting) is caused by the convergence circuit failing or a bad antenna connection.

Hitachi 61SWX10B... | 38 views | 0 helpful votes


If you wish to get more details, check this site. Pull up older posts there. Check the site with patience, as it has over 2350 posts now. All are related to electronic equipment repair help. If you check the site in Timeslide option, which can be selected from the dropdown list at the top left side of the display window, it will make search easy. Details about convergence adjustments have been described with illustrations.
http://electronicshelponline.blogspot.com/

Hitachi 61SWX10B... | 36 views | 0 helpful votes


Try to Google the model number, about the only way I can think of to find this information. It was at least 2,000 at one point.

Hitachi 61SWX10B... | 22 views | 0 helpful votes


Very common problems for DLP tvs,will get worst as times go by.Tv probally have a problems known as a convergence problems,it is dead.Tv have colors lines R,G,B unlevel on the pictures?Crooked pictures have mis colors alignments?Yes.There is no way manually to do an adjustment to fixed for this.Try push the tv remote button that said Magic Focus button.If the tv have data processing never completely done and have a error message and stop.Ur tv 100% have a dead tv convergence board,the tv convergence board must have it parts to be replaced like 2 STK convergence ICS and some or all of it resistors too.Than tv will be able to run the tv remote Magic Focus again to have a 100% data processing with no error message,tv to fixed this problems.The shop will cost u like $300-350 for parts and labors.

Hitachi 61SWX10B... | 193 views | 0 helpful votes


You will need to replace Both of the Convergence ICs ,Located on the left hand side board in back of TV. They are Big Black ICs and will have the part Number on them STK392-110 use the 120s.
Mats has ICs ,but tell them you want the convergence Kit for your Model it will have ICs and Resistors that come with it. ,You will also need to check Low Ohm resistors in the same circuit.
Mats Electronics 1-800-628-1118
PS. What ever you do (DO NOT) Clear the DC Ram if you do, it Takes over 6 hrs to realine convergence.

Hitachi 61SWX10B... | 49 views | 0 helpful votes


There is most likely an issue with the Surround PWB since you have the DP17 chassis. I would check the following items on the surround board. I have seen them all several times with the DP17

IT02 Shorted, pins 92 and 93 caused by Solder splash. IT02 Is also known to fail. Also pins 42, 43, & 44 have been known to have cracked solder
IT05 pins 20 & 21 shorted also Seems to have been caused by too much solder.

IS13, pins 1 & 2 shorted ( too much solder

Also check for cracked circuit trace patterns under IT05If you need further assistance let me know.

Hitachi 61SWX10B... | 67 views | 0 helpful votes


Ur tv have a problems known as a convergence problems it dead.Tv have colors lines like R,G,B mis alignments,have colors shadows pictures or 3D pictures look alike?Tv have a dead convergence board,board must require replacing 2 STK convergence ICS and some or all of it resistors too.To fixed the convergence board to solved the tv picture convergence problems.The shop,will coat u like $300-350 for parts and labors.

Hitachi 61SWX10B... | 311 views | 2 helpful votes


http://www.tvrepairkits.com/xcart/home.php?cat=1600


Here you go, figured I'd just give you the best link for the EXACT kit you need. (includes step-by-step picture instructions)


Please rate if this helped :)

Hitachi 61SWX10B... | 47 views | 0 helpful votes


Not all DVI inputs are the same. Do you have the manual handy to see if it supports analog DVI?

If it does, you should be able to just use A VGA cable with DVI adapter from your computer to the TV, Select the DVI input on the TV, and make sure your computer display settings are correct (this depends on a few things, so if you need help with that please reply back with more detail about your PC setup)

Hitachi 61SWX10B... | 175 views | 0 helpful votes


The convergence repair kit for your model is available at www.tvrepairwporld.com which should solve that problem. The kit does include the parts and the CD with instructions for the repair.

Hitachi 61SWX10B... | 42 views | 0 helpful votes


Check ur power source?Yes,wait like about an hour later for the tv resetting back to it factory setting.Recheck all connections inside of the tv for loses or untighten connections?Make sure all connections are tighten and no damage to all the PCB boards tries again tv should work now.

Hitachi 61SWX10B... | 77 views | 0 helpful votes


You need to get into your menu and find where you can reinstall factory settings, or default settings. Also you can try the realignment......

Hitachi 61SWX10B... | 30 views | 0 helpful votes


your convergence ics are going bad.

Hitachi 61SWX10B... | 16 views | 0 helpful votes


www.tvrepairworld.com has the convergence repair kit for your model which includes the ICs , Reistors and the CD with instructions.

Hitachi 61SWX10B... | 252 views | 1 helpful votes


You just need to purchase and replace the projection bulb. That will restore the brightness back to factory new. The price should be about $90. Replacing the bulb isn't that hard but can be a bit difficult (actually annoying) if you have never done it before. If you can get a service guy to do it for you it will be worth the money. Figure about an hours labour for that.

I don;t know your location so can't help you find a repair shop. If you call either the place that sold it or any place that sells them they should be able to tell you who ro where to contact. This is a repair you can do yourself if you are comfortable with it. The bulb is screwwed down with 4 screws and there should only be one connector on that model. If you take your time and keep track of how you got in and what you took apart first then its pretty simple. It can be a bit daunting the first time which is why I would suggest a repair shop if you have any qualms.

Hitachi 61SWX10B... | 183 views | 1 helpful votes


You need to locate and replace both of the two convergence chips the set uses. Most likely they will be STK-392-110 BUT THE NUMBER WILL BE PRINTED ON THEM IN WHITE.

total parts cost if you can do it yourself will be under 30 dollars.

I will attach a photo of typical chips for you.

SD TECHsd_tech_25.jpg

Hitachi 61SWX10B... | 50 views | 0 helpful votes

Not finding what you are looking for?
Hitachi 61SWX10B 61" Rear Projection Television Logo

115 questions posted

Ask a Question

Usually answered in minutes!

Top Hitachi Televison & Video Experts

Jaime Hernandez

Level 3 Expert

2337 Answers

The Knight
The Knight

Level 3 Expert

76054 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Hitachi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hitachi Televison & Video

  • Hitachi Televison & Video

Most Popular Question

picture unstable jittery colors

  • Televison & Video
Loading...