20 Most Recent
Canon imageRUNNER 6000 Copier - Page 2 Questions & Answers
Canon ir 6000 ranning copy machine hang 2minet before e733
Dear
1) Turn off and then on the main power switch. Is the problem corrected?
YES: Check the operation once again; if normal, end the work.
Check Connectors, DC controller PCB
2) Is the connection of the connector (J1015) on the main controller
PCB and the connector (J122) on the DC controller PCB normal?
Further, is the cable between these connectors normal?
NO: Correct the connectors/cable.
YES: Replace the DC controller PCB.
Thanks.
2/7/2015 5:39:36 PM •
Canon...
•
Answered
on Feb 07, 2015
Canon ir6000 error code E0061
Dear
Select COPIER>DISPLAY>DPOT in service mode.
If the difference between VDM and VDT is less than 6V,then check laser scanning unit shutter mechanism. if more than 6V,then go 'Display COPIER>FUNCTION>MISC-P>PRE-EXP' in service mode.Check if the preconditioning LED lights. If the LED does not light, replace the LED.
if problem not shut out check all harness related to DC CON pcb to LSU. Cross check the LSU and DCCON pcb.
Check the ram cleaned.
Thanks.
1/20/2015 11:53:45 AM •
Canon...
•
Answered
on Jan 20, 2015
E000602-0004
E602-0004
An error occurs by checking the Control Table of "Image storage area" when the machine is "ON"
I would try the following, under service mode goto:
Copier->Function->System
Set Chk-Type to 1
Execute HD-Clear
Set Chk-Type to 2
Execute HD-Clear
Power the copier off then on again.
Also make sure you are running system software v31.04 or later.
1/20/2015 11:40:19 AM •
Canon...
•
Answered
on Jan 20, 2015
Canon ir6000 error code is morning E0061
Dear
The mode selection has problem, pl. check the laser unit shutter, LSU and DC controller PCB.
The above are the measure if the error code has no sub-error.
Thanks.
1/19/2015 2:34:24 PM •
Canon...
•
Answered
on Jan 19, 2015
Canon image RUNNER 6000 Copier
error
A E000001-0000 is a error code for the fuser unit. It means it is not warming up to correct temp. Also, it may show up after a power surge or power lose. You may be able to reset it in service mode.
1/5/2015 6:01:56 AM •
Canon...
•
Answered
on Jan 05, 2015
Error 0732-0001
Error Communication Of both IP Bord And Feary Bord. plz Cek the connecter. or change the IP bord.
7/24/2014 4:16:06 AM •
Canon...
•
Answered
on Jul 24, 2014
Toner waste replacement
Remove the two screws, and detach
the cover from the right rear bottom
of the machine
2/17/2014 3:41:19 PM •
Canon...
•
Answered
on Feb 17, 2014
When i put my canon
Hello,
this is error code for main motor failure, you can try to reconnect main motor, look for breakege of gears, reconnect dc controller, or the main motor must be replaced or dc controller, or ...
As you can see that there is a lot of things that can be fault, so call service!!!
1/21/2014 1:34:41 PM •
Canon...
•
Answered
on Jan 21, 2014
Describe how to remove hard drive from canon
what you will have to do is remove the back cover.
then you will need to remove the thin metal cover laying flat cover on the back half of the copier just under the doc feeder. should be 3 screws.
then there is a metal box that holds the main controller on the right. if you open that you will see the IDE cable which will run up and out of that box and will run up under a thin metal plate that should be held in by 2 screws. if you remove those screws you should be able to see the hd .
if you can't get it out and or find it please call me it might be easier to explain. over the phone.
C & S Canon Copier Repair
(858)414-8475
1/10/2014 8:00:57 PM •
Canon...
•
Answered
on Jan 10, 2014
Not finding what you are looking for?