20 Most Recent JVC KT-SR2000 SIRIUS Radio Receiver with Car Kit Questions & Answers

Ditto - JVC KT-SR2000 backlight doesn't work (watched die yesterday), after 2 years, 10 months. Sadly JVC no longer represents quality.  
Note: Original JVC KT-SR2000 was a fire hazard - defective from start - overheated hardly describes it. BestBuy replaced first month. 

1506

Unfortunately the Ford V Serial Number codes are only available from the Ford Main Dealer.....................or a Decode Service who will plug your radio into a laptop and read/recode the memory chip

HI. I lost my code for radio ford focus serial number M227636

1645

Does the radio work if the dash lights are off?I'm wondering if the power and lamp wires are reversed in the 3 wire connector that plugs into the side of the radio.satellite radio receiver

It's a bad Sirius tuner. You can find them on ebay for 50 or so rebuilt and they are better than new. It's cold solder joints on the antenna input plug. Hope this helps

I have the same problem. It's happened twice now. Each antenna has lasted about 1 year. The connection is good, the antennas just stop working. It's almost like there's some built in life span. Who knows. It's ridiculous either way.

Antenna Not Detected. Now I have to buy a new one AGAIN $39.00 and re-wire thole whole thing in my car. PITA

It is not likely you could. The key (not the fobs) are a passive device that would not be able to receive enough power to rewrite any code within itself.

your code

1210

Sorry I can't help. I'm having the same problem. Seems to be a common problem with these units. I posted the same problem. If you get an answer before me could you please forward it to me and I will do the same for you. THANKS AND GOOD LUCK

It does have an aux input with two levels but this isn't suitable for a turntable. A suitable input should have RIAA correction with a sensitivity of just a few millivolts for a magnetic cartridge. Instruction manual can be found on the link below... http://resources.jvc.com/Resources/00/00/90/LVT1519-001C.pdf

Here is the user manual; https://www.manualslib.com/products/Jvc-Th-A75r-252593.html

The sound you're hearing could be due to a variety of reasons, such as a loose connection, a malfunctioning component, or a power issue. Here are some steps you can take to troubleshoot the issue: Check the speaker connections: Ensure that the speaker wires are properly connected to the receiver and the speakers. Make sure that the positive and negative terminals are correctly aligned. You can also try disconnecting and reconnecting the wires to ensure a secure connection. Check the power source: Ensure that the receiver is plugged into a working power outlet and that the power cord is securely connected to the receiver. You can also try plugging the receiver into a different power outlet to see if that resolves the issue. Check the volume level: Ensure that the volume level on the receiver is not set too high. High volume levels can cause distortion and other issues. Reset the receiver: Try resetting the receiver to its default settings. To do this, turn off the receiver and unplug it from the power source. Wait for a few minutes, then plug the receiver back in and turn it on. If these suggestion don't help, you may have to seek professional repair.

A bit of basic knowledge is required first; Insert CD, the first thing the processor expects is to scheive Focus. When Focus is acheived, the Spindle Motor will turn. Either the Laser cannot Focus or there is an issues with the Spindle Motor. Which is it ... if you know, then you will know which part or board has the issue.

Question edited for a lot more clarity and toss in a load of CAPS. Can you hear the CD Motor spinning? If so, probably this https://www.fixya.com/support/r29927004-dvd_player_or_cd_player_not_reading If not, the CD Unit has failed, or the power supply to it. A JVC Service Centre should be able to fix it. ..

Question edited for clarity, toss in some CAPS, add the Magic word. Strangely there is no owners manual but there is a Service Manual for it. It appears that it is actually a 'JVC FS-2000GD'? Normally turning off the alarm just requires pressing the Alarm Set button one more time to toggle it off. Or you can disconnect it from the mains, remove any back up batteries if it has them and it will reset everything. Then set the time.

JVC FS-2000GD Service Manual download, schematics ...

Elektrotanya https://elektrotanya.com > download ·Translate this page Download JVC FS-2000GD service manual & repair info for electronics experts.

Download service manual. Operating instructions are also given in english. JVC CA-D8T SM Service Manual download, schematics, eeprom, repair info for electronics experts (elektrotanya.com)