Top 20 Zenith XBS448 System Questions & Answers

The batteries are not powerful enough. Replace them again with good quality 1.5V units (not 1.2V Rechargeables).

unless the security camera has a setting for recording the date stamp you probably can't. The camera probably has a setup tab to enable embedding the date stamp on the video.

It is an old 2007 Set. Upgrade the television, the soundbar has left it behind in software terms. https://www.manualslib.com/manual/646773/Zenith-Z42p3.html#product-Z50P3%20and ..

It's possible that there could be a problem with both record players. Here are some things to check: For the Swingmate Concert Hall Automatic Record player:

• Check to make sure the power cord is securely plugged in and that the outlet it's plugged into is working.
• Check to see if there's a power switch on the back of the record player that needs to be turned on before the main power switch can be activated.
• Check to see if the main power switch is stuck or blocked in some way. If so, try gently pushing or pulling it to see if it will move.

For the Zenith 4 speaker stereophonic record player:

• Check to make sure the power cord is securely plugged in and that the outlet it's plugged into is working.
• Check to see if there's a power switch on the back of the record player that needs to be turned on before the main power switch can be activated.
• Check to see if the knob is stuck or blocked in some way. If so, try gently pushing or pulling it to see if it will move.
• Check to see if there's a safety mechanism preventing the turntable from starting up. Some record players won't turn on if the tonearm is not in the correct position or if the record player cover is not closed.

If these suggestions don't work, it may be best to take the record players to a professional technician for further inspection and repair.

Some have a backup battery in the back or the base. Flashing normally is an indication that here has been a power cut.

Sounds like a bad potentiometer Here you go. Click here: https://www.hifiengine.com/manual_library/zenith/mc7050.shtml

Seems impossible to find. There was directions posted on FixYa which gave directions to a different Zenith models. While not the same, you may find the directions to this model similar to your Z358.

http://www.fixya.com/support/t23768010-set_time_zenith_z1233ba

Press "display" and make sure the radio is displaying frequency, not time. Tune the radio frequency you want to add to memory. Press "Memo Set" and observe that "preset" flashes on the display. Press the number of the memory channel that you want to save to. Press "Memo Set" and observe that "preset" on the display has stopped flashing. The frequency is now saved the selected channel.

Disconnect your speakers when unit off and cold. Turn unit on and wait. If unit stays on, check speaker wiring for damage. Connect one speaker at a time with unit off and retest to find either a bad speaker or output channel problem. Repair speakers and wiring if found, or take unit for service, you have an overload problem.

remove the flat rubber platen cover to expose the lock ring at center (horseshoe clip) remove this lock ring and pull the platen straight up and off , under there you should find a rubber tire and the drive motor shaft , turn unit on , you should see motor turn and then it should move rubber tire , if not , your going to need to replace it or clean it up and lube it

Cassette tapes began to supplant 8 track in the mid 70's, so this is probably a transitional unit. Kind of like now - there are DVD players out there that still have VHS slots. I'd say late 70's and I'd guess no tubes.

Is there a "sleep" button?

Please visit the following website: http://www.vintage-radio.net/forum/index.php They should be able to help you solve this old radio problem.

it is set for the wrong time zone,it needs to be 1 before or 1 after yours,read your manual,i dont have one

And I did run agains this: But I don't know where to send it? 5 Mb would work with a Gmail account.

March 5, 2015. I'm selling these Zenith Z1233BA Clock Radios on ebay. I have sold about 10 without any problems, but someone just ask if I know where the get the instructions. I could not find the manual online. Here are some of the basic. To set the time set the lock button on the bottom to off, press the clock button, the clock will flash then use the set buttons on top to change the time. Use the <> to change the time, when the time is set press and hold the enter button until you hear a beep. You have to cycle through all the minutes to get to the next hour. Do the same to set the zone. And to set the Date select the CAL button and do the same as setting the time. Put it back on lock when the time, date and zone are set. To set the Alarm press the Alarm Set button then use the set buttons on top change the Alarm time. Use the <> to change the Alarm time, when the Alarm time is set press and hold enter until you hear a beep. Press the Alarm On/Off button to select radio or buzzer for the alarm or alarm off. To set the PRESETS tune the radio to the station you want to be a PRESET, then press and hold a PRESET button until you hear a beep.

0247 0544 0601. Try these codes. If you wish to get more; check the sites linked here. It has set-up code list & set-up procedure to many popular brand remote controls. See it in "Mosaic" or "Magazine" view. It will make surf easier. Or, do a search by type in the brand name of your device at its search box, and press "Enter". http://electrohelponline.blogspot.com/ Check this link too. http://remotesearch.blogspot.com/

Check your power wire from battery

check the fuses if there are any within the unit as this often happens during a power surge or power outage due to storms and lightning

send more detail about remote