20 Most Recent Durabrand DU1901 TV - Page 3 Questions & Answers

Try 0178 or 0180, If you need a manual for your all-for-one remote you can download it at http://www.oneforall.com/support/manual
Please rate this solution. Thanks.
0178, 0180
0178, 0180

If you don't have the yellow, red and white RCA jacks on the set anywhere, an rf modulator would be the simplest way to go. Then all you will need to do is put the tv on ch3 or ch4 depending on what the modulator is set to.

RCA Universal Remote Control Programming Codes

Programming Your Universal Remote.
The remote may already be set up to operate your brand of TV, VCR, orCable Box. It is pre-programmed with following codes:

• TV-000
• VCR-000
• Cable Box-000
• AUX is programmed with VCR code 037

For brands thatrequire programming, there are two ways to program: Using Code Lists orCode Search. Use Code Search if the code lists are not available or ifthe codes from the lists do not operate a device.

Programming a Device using Code Search:

1. Manually turn ON your device (TV, VCR, Cable Box)
2. Press and "HOLD"CODE SEARCH
3. Press and release the device button you want to set up (TV,VCR, Cable Box) However, if you are using AUX for a device, press and releaseAUX first and then the device button for the type of device to be programmed(TV, VCR, or Cable). The selected device button will flash once.
4. Release CODE SEARCH.
5. Press OFF/ON repeatedly until the device turns off (youmay have to press up to 100 times at a rate of once per second).
6. Once the device turns off, press and release ENTER.
7. With the device on, pressany other button. If the device responds, no further programming is required.If the device does not respond, repeat steps 1-6.

Programming a device using the Code Lists:

1. Find codes for each device and brand below.
2. Press and "HOLD"CODE SEARCH.
3. Press and release the TV, VCR or Cable button you wantto set up. If programming AUX for a device, press and release AUX firstand then the device to be programmed (TV, VCR or Cable). When the selecteddevice button flashes proceed to the next step.
4. Enter the three digitcode from the TV, VCR or Cable Box code lists.
   
5. Release CODE SEARCH.
6. With the device on, press another button, for example CHANNEL UP. Ifthe device responds, no further programming is required. If the devicedoes not respond, repeat steps 1-5 using another code number from the lists: RCA Code List

Also can review another Remote Code List

I hope help you with thi, Good luck.

A blown fuse is a result of a failed component it electronic circuits. Replacing the fuse wont do no good. I fix television, and I wish I could show you how, but it has too many terminology, and rquires at least basic electronic understanding. Electronic device are the only thing a really good handy man can't fix. They are extremely complicated.

check the speaker first

For the GE Universal Remote (RC24991-b), 0157 works (for me) with this Durabrand model

My Daughter has the same problem with hers. That high pitch noise your hearing is coming from
a transformer on the inside it means the transformer went bad and has to be replaced.I hope this helps a little.

Los codigos de tv admiral son los siguientes 001,046,047,083,095,173,191.,espero que te sirvan.

Turn off the text box with the TV/CAP/TEXT button. Go into the menu and change from TV to CABLE. Run the AUTO CH MEMORY.

Go into the CH SET menu. Go to the TV CABLE line. Set it to TV for antenna reception or CABLE for cable without a cable box. Go to AUTO CH MEMORY. Press the VOL + button to start the channel search. WAIT until search screen goes away. Check ALL your channels. Hope this helps.

When trying to program a universal remote for the BH2004D, try the codes that came with the universal remote for HAIER.

Try bringing up the menu by holding both volume buttons down at the same time (or use menu button on remote if you have it). Go into CH SET using the channel and volume buttons on the front of set (or use the SET + and - and the ENTER buttons on remote). Go to the TV CATV line and move the arrow to CATV. Let menu time out. This will put tv into cable mode. Hope this helps.

The digital Cable conversion only effects those who still get their TV channels through an antenna or rabbit ears. If you get it through a cable provided like Comcast, you SHOULD be fine. For more information, look at the FCC website.

Happy viewing :)

http://www.dtv.gov/consumercorner.html

Most stereos like that have a fuse inside. I would take off the the cover and check for one. It should be close to where the power cord connects to the circuit board

Durabrand tv's were made for Walmart by Orion, Funai, and Haier. Look under those names in your code list. I hope this helps. friend of nx.

Press the TV/AV button on the remote.

Use your sky remote you can tune it to your TV, all the buttons will be in the wrong place so you will have to play around with it.
It worked for me.
John

Here's the link to codes for RCA remotes. Try codes for ORION, SANSUI, EMERSON, and RCA.
http://remotefinder.rca.com/default.aspx?site=rca

phone number for durabrand tv company

http://www.fox-international.com/