20 Most Recent Mitsubishi VS-60607 TV Questions & Answers


Well if your tv is older like the one in the pic it sounds like the bulb is overheating, you may want to vacuum the dust out of the back and make sure it isn't got block of air flow in the back and also make sure it isn't up against a heat source

Mitsubishi... | Answered on Feb 19, 2018


Projection tubes need replaced. They will only work once they are warm, so they are wore out.

Mitsubishi... | Answered on Sep 20, 2014


Probable power supply failure

Mitsubishi... | Answered on Apr 20, 2014


Sorry Dean but it is not worth the fix. You will run into other problems with this unit . It is 14yrs old and has lived a good life. Far beyond others.. Industry standards are 5-7 yrs for consumer electronics (televisions in general). Take a look at the LG LEDs.

Mitsubishi... | Answered on Mar 16, 2014


Here are the two top reasons that can cause the 60607 to throw a 23 or 24 code. Check these items then let me know what you find.
1. CHECK SOLDER CONNECTIONS AT CONNECTOR "DY" ON THE YOKES. 2. CHECK C411 2200 UFD 35 V AND C412 10 UFD 50 V, BOTH LOCATED ON THE MAIN PCB.

Mitsubishi... | Answered on Dec 24, 2013


Standard tv

Mitsubishi... | Answered on Oct 23, 2013


coul'be overheat solder the cause of a loose connection , and or convergence ic 's almost ready to fail . the cost to repair will be around 250.00 to fix replacing the ic's depending of the tech. or 350.00 at repair shop if you may have more question , let me know Im here to help you. thanks

Mitsubishi... | Answered on Jul 14, 2013


Model number given indicates it should be a 2000 year model.

If so, it should have the self check feature; try to turn the set on and when the green light goes off: On the front of the set press and hold both the menu and input buttons for at least five seconds and then release both buttons.

Power light will blink a two digit error code like: 2 blinks,pause and 2 blinks (2,2 error code is most common one). It will repeat the error code several times.

Let me know what error code you find and I will tell you what it may mean.

if this told you something you did not know rate this solution as "very helpful" as I do this here for free.

You can post a comment on this page.

Regards, SD TECH

Mitsubishi... | Answered on Mar 27, 2013


this isn't a notorious problem. many problems can cause this. the instant on/off behavior just says there is one of many fuses blown in the television. you can't just replace the fuse, when it fails get a failure code find out what it means and repair the problem. I would recommend paying someone to do it if you don't want to trash your mits set.
to get the code you hold down the menu and input button for 5 seconds after the on/off sequence. it is a 2 digit code with a pause inbetween, example 2 pause 2 pause 2 pause etc. is a 2.2 code

Mitsubishi... | Answered on Feb 03, 2013


Cannot be done as needed buttons are only on original remote---The good news is almost any Mitsubishi remote made over several years will have those---EBAY?

Mitsubishi... | Answered on Nov 08, 2012


Check entering this master rest code [4768].

Mitsubishi... | Answered on Oct 27, 2012


ONLY 1 of 2 things can cause this problem----

First thing to do is remove front speaker grill--it should pull out and issecured with plastic pegs--behind it you will find an inspection plate---

Notice the one or two pairs of wirescoming from the front keyboard of the set---remove the inspection plate andfollow the wires to the right--you can unplug both plugs(most have two and theyare marked with letters and different s so you cannot get them wrong)

The idea here is to remove the front keyboard with its reset button etc fromthe circuit---You will still be able to try to turn the set on with theremote---

These sets have a Receiver that is called a DM board--(large metal box to theleft as you look from the back) and if the power goes out the green light willblink for about 70 seconds and then go out---it is the Receiver booting up. Itis called the DM board.

If disconnecting the keyboard allows the set to turn on--you have a bad resetswitch and two choices---either operate the set only with the remote or toremove the front screen and get at the reset switch (it is tiny) and removeand/or replace it.

If disconnecting the keyboard does not restore the set to operation---thereceiver is bad---there are 4 or more caps and some pico fuses that can fail inthat unit---Mitsubishi no longer sells or repairs these--if it is bad and notthe caps there is a company you can send the unit to and have it repaired--ifyou need to know their name let me know---

You can call them and get a quote for repairing the receiver.


Let me know what more information you need--I am here to help.


SD TECH

Mitsubishi... | Answered on Jun 12, 2012

Not finding what you are looking for?
Mitsubishi VS-60607 TV Logo

131 questions posted

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1255 Answers

The Knight
The Knight

Level 3 Expert

76046 Answers

Jaime Hernandez

Level 3 Expert

2337 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Mitsubishi Televison & Video

  • Mitsubishi Televison & Video

Most Popular Question

mitsubishi vs60607 n started flickering

  • Televison & Video
Loading...