20 Most Recent Minolta EP1031/1031F CS/PRO Copier - Page 8 Questions & Answers

0helpful
1answer

Konika Minolta 215 coud c3752

hold clear/stop and power on the machine if the code comes back replace the fuser do not reset agian as the fuser can start a fire that will ruin a good day Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
4/7/2018 9:03:15 PM • Minolta Office... • Answered on Apr 07, 2018
0helpful
1answer

How do I clear a SC35-02 code on a di650 Minolta copier ?

sir/mam Power off the machine power on with the 2 and 5 depressed. Then go to soft switch set 3-1-1 if the code comes back its the fuser have a tech look at as it can start a fire ruining a perfectly good day Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
4/7/2018 9:00:49 PM • Minolta Office... • Answered on Apr 07, 2018
0helpful
1answer

Does anyone actually know what the procedure is to clear an SC35-02 .I haven't worked on one of these in 10 years DI650 Minolta copier

Power off the machine power on with the 2 and 5 depressed. Then go to soft switch set 3-1-1 if the code comes back its the fuser have a tech look at as it can start a fire ruining a perfectly good day Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
4/7/2018 9:00:19 PM • Minolta Office... • Answered on Apr 07, 2018
0helpful
1answer

Minolta photocopy machine 6001 I had a toner in the developer The photocopy brings a simple page of the machine, what is the solution to it?

Mam, this is a very legacy machine! But, did you replace the developer??? Not the toner, you need to buy developer for this machine , before replacing the developer clear the counter in service mode, after replacing the developer you need to run the F8 procedure, adding toner is not going to help. After running F8 run F5 Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
4/7/2018 6:10:31 PM • Minolta Office... • Answered on Apr 07, 2018
0helpful
1answer

I need help to clear error 18 on konical minolta 240f.

https://printcopy.info/?l=en&mod=erc&brand=Konica-Minolta&model=bizhub%20240F&code=18 Konica Minolta bizhub 240F Error Codes Quoting from the web link shown above: Konica-Minolta bizhub 240F Error Codes

Exploded Views and Parts List Free!

Code

18

Description

Fuser Error (The number indicates the detailed error code) 0 The fuser did not become to the main motor driving temperature in 50 seconds after printing started. 1 The fuser did not become to the paper pick-up temperature in 50 seconds after printing started. 2 The fuser did not become to the main motor driving temperature in 30 seconds after warming up started. 3 The fuser did not become to the warm-up finishing temperature in 30 seconds after the motor started driving. 4 A temperature of 250°C or higher is detected in a mode other than sleep mode. 5 The fuser does not warm after fuser error is solved and the power is turned OFF/ON. 6 A low temperature of 10°C is detected in 10 seconds after printing started. 7 A temperature of 190°C is detected in ready mode after printing finished.

Remedy

1. Turn on the power again, and verify the fuser warms up. If it does not, see step 4. 2. Check the contact between Fusing thermistor and Connect A PCB(P89). 3. Check the contact between Connect A PCB (P80C) and the main board. 4. Replace the Fuser. 5. After replacing the Fuser, verify the fuser warms up when the power is on. 6. Replace the main control PCB.
4/7/2018 3:08:26 PM • Minolta Office... • Answered on Apr 07, 2018
0helpful
1answer

How can i adjust konika minolta bizhub 420 tcr

You dont adjust the TCR it is developer to Toner ratio. Inside the developer unit. You replace the developer if required Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
3/18/2018 10:05:33 PM • Minolta Office... • Answered on Mar 18, 2018
0helpful
1answer

Minolta c650 code P22

Clean the sensors under the transfer belt, the black drum recommended be replaced. Since Black is what all the colors are aligned to. To clean sensor requires removal of the Transfer belt be careful as any damage to the belt will result in copy quality issues Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
3/5/2018 12:06:59 AM • Minolta Office... • Answered on Mar 05, 2018
0helpful
1answer

Respectd,sir my di520 minolta machine error c-0510 i check the thermistor ,fusior not damage pleses guaide .

FIRST, if this code comes back. Have a technician look at it DO NOT CONTINUE TO RESET the code!!!! AS this is for the Hot Part called the FUSER. It can catch on fire! And that will ruin a perfectly good day!!!! Open the front door of the copier, copier must be on. Look to your upper left, you should see a small cover with a screw remove and the cover. Inside you will see a small button, press it that should reset the copier. AGAIN if this code comes back. Have a technician look at it DO NOT CONTINUE TO RESET the code!!!! AS this is for the Hot Part called the FUSER. It can catch on fire! And that will ruin a perfectly good day!!!! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
3/5/2018 12:02:16 AM • Minolta Office... • Answered on Mar 05, 2018
0helpful
1answer

HI, I HAVE Minolta DI520 When i On Mchine its ok after ready press Print Button same time C0220 error come can you help me to solve this problam thanks.

Remove the drum unit and clean all contacts on the rear of the unit and inside the machine where they would contact. you mite also want to replace the drum unit (worse case the HV(High Voltage) and or the Main board are bad), when was the developer and drum changed. Quite a legacy machine!!!!!!!!. Was built before Minolta and Konica became one!!!! Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
3/4/2018 11:55:02 PM • Minolta Office... • Answered on Mar 04, 2018
0helpful
1answer

Fix error 111 code on Minolta c454e

missing number in the error code it will be c-XXXX Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
3/4/2018 11:48:32 PM • Minolta Office... • Answered on Mar 04, 2018
0helpful
1answer

Minolta cspro ep3010 negative print problem plzz tell how to solve this problem?

explain the negative print?. But check the drum and or scanner have you run the F5 or F7? Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
3/4/2018 6:53:53 PM • Minolta Office... • Answered on Mar 04, 2018
0helpful
1answer

My minolta ep 3000 machine not booting up only display welcome on screen and hang up. Plz help me out from this trouble.

That is a very old machine, try open closing front door does the screen display any codes? open front door upper left small access plate remove and push reset switch Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
2/24/2018 7:23:30 PM • Minolta Office... • Answered on Feb 24, 2018
0helpful
1answer

ERROR C-2703 IN KONI KA MINOLTA BIZHUB PRESS C1060

Check the charge Corona Assy unit for cyan (Blue) Open front covers Pull out mid section NOT paper section (have to unscrew two screw to open this section one to the left of the unit the other upper left just below the control panel. Should see four devices that look like they could be pulled out with your thumb. one each for each drum pull them out check that the very thin wire below the grid is not broken the re-seat each one check the all might as well. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
2/24/2018 7:03:50 PM • Minolta Office... • Answered on Feb 24, 2018
0helpful
1answer

Minolta Bizhub 250 error Code c0211 And bay pass problem tray 1and tray2 not work I mean page not pik

Well the code C-0211 is the bypass tray. Check that there is nothing near the lift section, remove the rear panel of the bypass tray check the connectors. Might have a bad sensor or clutch. As for trays one and two check for paper behind them!!! POWER OFF first and Remove the draw(s). If paper not picking up have tech come out and replace the rollers in each draw and the by pass tray. Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
2/24/2018 6:56:18 PM • Minolta Office... • Answered on Feb 24, 2018
0helpful
1answer

Sagem mf 3175 fax not responding

check the phone line is it analog or digital if digital must be analog Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f
2/18/2018 9:45:33 PM • Minolta Office... • Answered on Feb 18, 2018
Not finding what you are looking for?
Office Equipment & Supplies Logo

58 questions posted

Ask a Question

Usually answered in minutes!

Top Minolta Office Equipment & Supplies Experts

Norman Weimar
Norman Weimar

Level 3 Expert

7035 Answers

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Daniel Blask
Daniel Blask

Level 2 Expert

232 Answers

Are you a Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Minolta Office Equipment & Supplies

  • Minolta Office Equipment & Supplies

Most Popular Question

try print gives me blinking j

  • Office Equipment & Supplies
Loading...