20 Most Recent Minolta DiALTA Di183 Copier Questions & Answers


Power off the machine. Then remove the toner bottle, be careful the hole might be on the bottom and the toner is going to go everywhere. Then close the toner cover and turn on the machine. Let the machine go through it normal routine. When it asks for toner install the toner bottle correctly. If THE KNUB on the side of the bottle is damage put a new one in. That KNUB is what the toner motor uses to turn the bottle, if it damaged you get a code. If that does not work you might have a bad motor or the home sensor or actuator for the toner bottle is bad worse case the control board is bad.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Nov 21, 2015


Well need to replace the drum and developer running F8 with out changing the developer is not good, also make sure you clear the counter before replacing the drum and developer done toghter

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Mar 31, 2015


manual by pass tray the tray on the right side of the machine is in op. Check for a jam that might not be letting the tray raise near the machine.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Mar 02, 2015


replace fusing unit cooling fan try the web site below as a start for the part Precision Roller Printer Toner Cartridges Parts and Supplies Office...

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Mar 01, 2015


replace the developer and the drum

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Mar 01, 2015


M1 is a counter for maintenance need to get service mode access to clear the counter and clear the message.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Mar 01, 2015


Press the panel reset screen until intial screen appears

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Mar 01, 2015


for the 0072 try this:

Power off the machine. Then remove the toner bottle be careful the hole might be on the bottom toner is going to go everywhere. Then close the toner cover and turn on the machine. Let the machine go through it normal routine. When it asks for toner install the toner correctly. If THE KUNB on the side of the bottle is damage put a new one in that KUNB is what the toner motor uses to turn the bottle if it damage you get a code. If that does not work you might have a bad motor or the home sensor or actuator for the toner bottle is bad worse case the control board is bad
As for the 0600 code the scanner the bright lite under the big glass is not lighting replace the lamp and board

as for the

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Mar 01, 2015


Does show any code on the screen like C0500 or something like that try turning it on with the stop button held down to reset the fuser (THE HOT PART) also check make sure the electrical plug is plugged into the machine tight and snug, if not sound like a power supply problem, might want to get a konicaminolta tech to come out a look at it.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Feb 22, 2015


Drum and developer need to be replaced and the counters cleared and the F8 run once the new developer is installed NC2 will go once that is done.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Feb 22, 2015


what code sir/mam?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Feb 20, 2015


Self Help Product Support Konica Minolta Business Solutions Inc


try this web site for op manual and drivers

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Feb 20, 2015


Never seen 5 Letter/number normally it C-13F0 or something like that please check again

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Feb 19, 2015


Could not find that code in the service manual?

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Feb 19, 2015


Well check all the door and covers make sure the doors don't have broken parts which go into certain sensor to tell the copier the door is closed.

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/normanj_7893313f0751935f

Minolta DiALTA... | Answered on Feb 14, 2015

Not finding what you are looking for?
Minolta DiALTA Di183 Copier Logo

95 questions posted

Ask a Question

Usually answered in minutes!

Top Minolta Office Equipment & Supplies Experts

Adorjani Laszlo

Level 3 Expert

1297 Answers

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6696 Answers

Marvin
Marvin

Level 3 Expert

81424 Answers

Are you a Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Minolta Office Equipment & Supplies

  • Minolta Office Equipment & Supplies

Most Popular Question

h2

  • Office Equipment & Supplies
Loading...