20 Most Recent GE Profile Performance WPSF4170WAA - Page 5 Questions & Answers

It is a job for the Service Techs, they have the special tools needed. videos https://www.google.com/search?q=ge+model+wjre5550h+replace+agitator+dogs ..

Claim on the guarantee as it has happened within the warranty. You need a new Water Inlet Valve. The solenoid isn't closing shut. The other possibility is that your home water pressure is too high. A plumber can test that and fit a pressure reduction diaphragm. https://www.google.com/search?q=ge+spacemaker+model+gud27essmww+water+inlet+valve ..

possible leak in soap dispenser or tube coming from it

Humming is normally caused by a failed start capacitor. Smoke would normally be the motor or wiring, but I am a little puzzled by the smoke inside the machine, and can only think there is a gap on the top of the drum to the top panel. In all likelihood, you need a new motor, but due to the cost of them, I would suggest getting a service tech in. Or you could remove the motor and take it to a local electric motor sales and repair outlet and ask if they can test the capacitor and motor. https://www.google.com/search?q=electric+motor+repair ..

Could be Drive coupling, Clutch dogs or Gearbox. Arrange a service call. They are all messy jobs and need a lot of stripping down and in some cases a special tool. There are ideas in the link. https://www.google.com/search?q=turn+the+bottom+half+of+the+agitator%2C+either+direction ..

Older models are easy. Connect the 2 wires together and bi pass the switch. Some washer use magnets if so do the same. I’m not sure about new washers.

possible power transformer bas on washer

google from manufacturer or go inside unit there should be a instruction book in by motor

possible bad drive motor thats overloading

check belt to motor if ok try under agitator the cogs are worn so replace them

The door switch is defective. It stops the machine from spinning when the lid is opened. Go to repairclinic.com for help and parts

Washer - Resetting the Electronic Controls - All GE Appliances ...

https://products.geappliances.com > appliance > gea-sup... To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a ... ..

Check to make sure that the washing machine is fully plugged in and then next, check to see if there is a tripped circuit breaker. Reset the breaker and try to turn on your washing machine and try to start the washer.If it still is not turning on then it is a damaged power cord that needs to be replaced.

The Agitator In your washer has two parts. The bottom half will move back and forth. The top half (spindle) will move in one direction (clockwise). Most of the scrubbing or washing is done by the bottom half of the agitator. The spindle is responsible for pulling the clothes down from the center and sending them to the bottom where they will be scrubbed. As the clothes circulate, they will all be washed.

Even though you replaced the seal, did you use proper lubrication when you put it on the shaft? It may also require a special tool to place the seal so that it does not get damaged. Last but not least there could be "run out " on the shaft due to bearing wear or the shaft is scored from the old seal.

call a local repair service .

if not working replace

The drawer normally is easily removed. Some have a latch, some you pull out and up. If you use powder, you may find a lump of it. The fabric softener section works using a siphon system and they can clog. Videos https://www.google.com/search?q=remove+dispenser+drawer+GE+Prodigy+Profile ..

Does only one letter look like an upside down F? If so, the code is probably tF, turbo Freeze. That actually indicates a feature in use. The coolant system should have the fan running on high, even when the door is open. Depending on the refrigerator, press and hold the Freezer button for 3+ seconds or press the Express Mode key to disable the turbo freeze mode. Since the refrigerator isn't cooling, clean the coils. Check for any areas that have ice on or near the coils. That will indicate a refrigerant leak and a service call is required. Check if the fan is moving. If it isn't, you may need to replace the fan or the motor. This fan circulates the cold air into the refrigerator. Next check that the vents between the freezer and the refrigerator aren't blocked. I hope this helps. For more specific assistance, please add a comment with the model number of the refrigerator. GE has built a number of french-door refrigerators and there are some differences in the parts between models over time. Cindy Wells

Capacities are 3.8 cu.ft or 4.2 cu.ft for the largest https://www.google.com/search?q=Capacity+of+GE+model+WWA8330BAL ..