Top 20
GE Profile JP930 Electric Cooktop Questions & Answers
LEAKING GAS VALVE
Hi,
The gas valve if it is leaking is not repairable...check the piping to and from first to make sure that you may be able to reinstall the valve and stop the leaking in the piping...soapy water will help identify the source of the leak...
That is not that hard to fix and you can easily buy the parts yourself online...Here is a tip that will help you with the online buying...How to Buy Appliance Parts Onlineheatman101
JP930 large right front dual
Hi, Sorry I missed this as it got buried in my emails. The part number for the switch you need is WB23M0009 costing about $70.00
OK, I have a cooktop that is discolored. Three
Sorry to read about your problem, I hope this helps you out.
you have to disconnected everything from the range, then take the unit out of the counter..will take 2 people
I tried to help you. Please help me and Rate/Vote on my response, thanks and good luck
How to un lock my GE Profile Induction cook top?
Try
turning off the breaker for at least 10 min and re apply power. If this doesn't
work, then there's an internal problem.
If after 10 minutes the cooktop is STILL locked:
Push the touch
pad that looks like a padlock for at least 5 seconds. The lock light should go
out.
I have a GE Profile
first check if power is getting to the cook top(there should be a box outside where the wire goes in. After that you have to check if the power makes it to the main board/connector to see if the individual burners are working. My guess is that there is a loose wire at the connection they redid when you redid your counters
Pot stuck to cooktop
Did you find that it was stuck after it had cooled off? A vacuum was probably created between the pot and the glass top. You could try twisting the pot, leaving it for a while, or heating it up again.
One of the burners does not work. Is it possible
yes,heating elemnt and the control can be chgd.to chg those pull the unit out and let it sit on the counter.remove all the screws around the stove just below the glass top.once the screws are out u can pull the top up and have access to all the components.make sure to turn the ckt breaker off b4 opening.u dont have to disconnesct the power cord from the wall if it is hard wired.
Burned Copper Bottom Pot on Glass Stove Top
sorry to say no , if you try to peal it off or scrape ot off you will crack the cooktop . this keeps happening i have seen it at around 4 times for some reason revere ware melts . there should be a warning in the manual ( i know ge does have the warning about copper bottoms ) . replaceing the cooktop or the whole stove is the only "true" answer .... sorry .....Please if this answer helped , please rate this 3 or 4 stars . and keep me in the paid answer department . A 1 or 2 may knock me down into the unpaid ranks. Thanks Cactus Bob
Cooktop glass broken - need a replacement - where can I find it?
It all depends on our capabilities... The top isn't all that difficult to replace. If it were me, I would call GE Factory Service 1-800-432-2737 or schedule an appointment online at www.geappliances.com as there may still be a warranty on the top which is expensive...
Counter top stove burner won't light
Hi, You asked a very generic question but I will try to give you a good answer. If the pilot is good and you can light the burner with a match, (this checks everything else) then the most common problem would be the burner holes in front of the pilot are clogged. When cool, remove the burner and inspect the holes, any debris needs to be removed, a bent paper clip works really well. Compressed air helps as well. If there is a tube to the pilot make sure it is exactly where it belongs and that it is clean. If the match didn't light the burner or the flames is not all blue like the rest, there is something else wrong and you need to get back to us with a make and model to better help you. Make sure the burner gets seated back on the orifice correctly and best of Luck to you!
Can't get GE profile cooktop clean
the problem is you didn't clean the unit before you used it the first time w/ the ceramabrite wax. the glass on your cooktop is porous and unless you seal it before ever using whatever went into the pores originally will always be in the pores and no amount of cleaner will get it out.
Dual Surface Selector Switch
more common is the dual switch to be bad, but it is possible that the elemnt itself has burnt out, usually a 5 yr warr on the elemnts under glass
Just bought a house, no manuals
After a pot spillover, the cleanup process triggered my stove top to "control lock"
I removed the pot and once the stove top cooled I pressed and held the "control lock" button.
It began to blink, I released it and then the light went off and the stove top operated normally.
You might not have to wait for the stove top to cool. I don't know.
GE Cooktop JP930 surface element not working
It sounds like the burner needs to be replaced. When they burn out sometimes they short out to ground. The cooktop will have to be removed from the counter and the glass top opened. You will probably be able to see where the element is burned out. Replace it and you should be fine. If it is too expensive to fix just disconnect the wires to the burner where they attach to the control . Then you can use the remaining burners. I really don't know what a replacement burner costs. An open coil is around $30.
Not finding what you are looking for?