Lakewood HV-18 Floor / Box Fan - Answered Questions & Fixed issues


blade pulls off... grab hold w 2 hands, pulling n wiggling with just enough force til it breaks free. Good Luck

Lakewood HV-18... | Answered on Dec 20, 2017 | 95 views


mcdevito75 here, If the fan is not too old I would figure yes, but a replacement motor will cost as a new fan, if not more, then you have to install and the blades are a presss fit to the motor.

Lakewood HV-18... | Answered on Sep 20, 2015 | 4,047 views


ok here is what I found....there should be screws on the outside rim where the two fan grates meet....then dust the innerds with a leaf blower or a rag, then use brake cleaner spray to soften the greasy dirt that formed, and again a rag to wipe away any residue....hope this works, it did for me

Lakewood HV-18... | Answered on Nov 16, 2013 | 395 views


I've had an 1887 since the 90s -- great fan. I have to say that FixinFax (Solution 1 above) probably didn't try to take his unit apart. My blade has stopped rotating several times over the years and I always got it going again by myself. I'm no whiz, just your average amateur handyman. In fact I am fixing the motherbleeper right now because in a week where the heat is 100 degrees it chose to slow down and stop.

Eventually it sucks enough dust into the axle housing so you have to take the motor mechanism apart and clean it. It's not terribly complicated, but you have to note how the electrical and mechanical parts go back together before disassembling. It's a little tricky to get all the housing parts to line up level again, you may have to try a couple times till the blade rotates freely. Wipe out all the dust and gunk buildup. Lubricate the axle with oil, or I just spray with WD-40. Then reassemble.

The only thing I have had to replace is the on-off knob, since it's plastic and it split. Just get a universal knob from your local hardware store.

Lakewood HV-18... | Answered on Aug 22, 2012 | 708 views


Try McMaster Carr -- page 640, Fans and Fan Blades.

http://www.mcmaster.com/#ventilation-fans/=8qgdv5

Lakewood HV-18... | Answered on Sep 08, 2010 | 251 views


Dust is evil to all mechanisms!! Keeep UNPLUGGED..then Vacuum all accumulated lint in fan motor assembly, and soak with WD-40...I just did detailed dust cleaning with toothbrush....Fan now runs awesome!! Good Luck

Lakewood HV-18... | Answered on Sep 06, 2010 | 178 views


you have 3 control wires (the 3 speeds) and a common wire. the common wire will go directly from the fan motor to the power source/cord and the other 3 leads will run through the switch. you could even use a standard dimmer-style lighting rheostat and connect it to the common and "high" fan speed wire and have infinitely variable fan speeds. hope that helps.

Lakewood HV-18... | Answered on May 29, 2009 | 1,429 views


hello martin you can buy a dimmer to slow down your fan
800 watt at least

Lakewood Dryers | Answered on Apr 30, 2019 | 31 views


Fixya is unable to suggest sources for Lakewood parts.

Lakewood Dryers | Answered on Jul 26, 2018 | 64 views


Fixya is unable to suggest sources for Lakewood replacement motors.

Lakewood Dryers | Answered on Jun 29, 2018 | 69 views


How do clean the lakewood mini tower fan model MTF 15

How do clean the lakewood mini tower fan model MTF 15

Here is what one said:
"To clean it, you will need a small paint brush, screw driver either flat or crossed, then disassemble it. Loosen the screw and just be observant what you put apart. Then clean it. Good"

You may want to take it to a gas station and REALLY clean it out? OR a aerosol canned "AIR DUSTER" will be very useful too!

Anthony

Lakewood Dryers | Answered on May 20, 2018 | 74 views


try any store that sells that make .

Lakewood Dryers | Answered on May 18, 2018 | 30 views


Fixya does not sell Lakewood fan switches.

Lakewood Dryers | Answered on Apr 01, 2018 | 87 views


Earl, take motor along with you, and visit some surplus stores, princess auto, etc.
I have often found parts like that.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Lakewood Dryers | Answered on Mar 03, 2016 | 243 views


hello Lamar baker i think the problem is the AC CAPACITOR is about 2 to 5 micro farad this is usually the problem if your sharp and bossing is clean and have oil...
25756704-xxq3bcvcyq5zxcxx4r2my2pa-4-0.jpg

Lakewood Dryers | Answered on Sep 24, 2015 | 325 views


The problem is you shouldn't have bought it in the first place. Low-end! Look for something with at least a 13 degree blade pitch next time you buy a fan.

Lakewood Dryers | Answered on May 30, 2014 | 41 views

Not finding what you are looking for?
Lakewood HV-18 Floor / Box Fan Logo

17 questions posted

Ask a Question

Usually answered in minutes!

Top Lakewood Dryers Experts

Bruce Showalter

Level 2 Expert

104 Answers

Craig Butler
Craig Butler

Level 3 Expert

1730 Answers

Steve Allison
Steve Allison

Level 3 Expert

5569 Answers

Are you a Lakewood Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...