20 Most Recent Napoleon Auburn Pellet Stove Heater - Page 3 Questions & Answers

The auger motor is fed through a high temp. limit thermostat. It has a manual reset on the back of it that you have to press on firmly to reset it. Open the side panel on the stove and find the wiring. You will see the thermostat on the back side of the combustion chamber. Look very closely and reset it.
good luck!
If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

The auger motor is fed through a high temp limit thermostat. It has to be manually reset if it activates but it could be causing your problem with a bad connection or intermittently bad. It deserves a look... If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

The auger motor is fed through a high temp. limit thermostat. It has a manual reset on the back of it that you have to press on firmly to reset it. Open the side panel on the stove and find the wiring. You will see the thermostat on the back side of the combustion chamber. Look very closely and reset it.
good luck!
If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

I'm confused by your question. If you are asking what is involved in installing a pellet stove well it varies greatly from model to model. Generally speaking, most pellet stoves will horizontally terminate behind the stove itself as opposed to running thru the roof like a woodstove does. Pellet stoves require the use of electricity for numerous functions, one of which is power venting thru this rear terminated pipe. As far as clearances to combustables, you will find that pellet stoves are very forgiving in that department, with minimal clearances required. Once again all stoves are different and they all are rated indepentently so my best advice to you is find a quality pellet stove dealer and go in and see them. They will be more than happy to answer your questions. Avoid the big box stores as they have pellet stoves at a good price but offer NO service or installation and believe me, I am in the business, you will need professional service at some point during the life of your stove so don't save a couple bucks by going cheap. You will be happier for it down the road. Good luck.

Hi Rose. check this link out might help you to find out why. https://www.google.com/search?q=Napoleon+electric+fireplace+is+beeping&rlz=1C1AVFC_enGB797GB798&oq=Napoleon+electric+fireplace+is+beeping&aqs=chrome..69i57.2722j0j7&sourceid=chrome&ie=UTF-8

turn everything off then turn back on some of these are like a computer reboot while system

??? - and the problem you need help with?

I hope you cut the gas off at the meter. This is called a runaway heater, and should not be used! The gas valve probably stuck open or someone has rigged it. Get a tech to check it out.

http://napoleondealers.com/files/W415-0949.PDF

What kind of regulator?

Be careful how you read the voltage on the ignitor, as it has a low resistance and may not show a voltage across it. As is the case with most parts, you can use a line cord to hot wire the device to test it. Remember, the stove has a 10 minute exhaust fan timer when its first plugged in, so the ignitor will not light until this has timed out.

Question edited for clarity. Question moved from Computers category. Yes if you swap everything that is connected to electricity over to 220 volts. It is marketed as a 110 volt spa eliminating the problems of running 220 volt power. https://www.google.com/search?q=lifesmart+ls350+plus+220+volt ..

Contact the manufacturer 1 800 863 3930 for specific information about this. The manual does not include information for getting rid of a general fault. https://www.alpha.com/download/outside_plant_power/cableups_power_supplies/broadband_ferro/install_oper_manual.pdf