20 Most Recent Bosch Classixx WFL 2066 Front Load Washer - Page 6 Questions & Answers

You've put the child lock on! When powered key press the on/off button for 5 seconds. This will remove the key!

Instruction Manual can be found here:
https://portal.bsh-partner.com/portal(bD1kZSZjPTAwOQ==)/PORTALFRAME.HTM

simply go back to the shop it was bought in and they have to supply with the instructions in english at your request at no further charge,email bosh at there customer services they will gladly supply you free of charg.adrian

child lock activated press start button for 5 secs or more will release refer to manual for info.

It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

If the water flows though the inlet then the flow pressure should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Test a pressure switch: Click on : http://www.youtube.com/watch?v=HZZ2bDMspj8

Check this link to replace the inlet valve:

http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the dry spin with the drain valve/pump activated so as to drain off all the water from the clothes during the spin. Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pu

It is possible that the machine does not start off the cycle because there are errors due to feedback from the inputs. For the program to start up the main program controller must initiate the INLET/MOTOR/DRAIN pump/ valve to open up and allow each function to be driven starting from the flow of water into the drum as also the drain valve to open to exit the water at the point of the program cycle. If this does not happen then the voltage at the valve/motor/pump must be checked or the fault relates to no voltage from the controller. This means the controller is a suspect.

If the water flows though the inlet then the flow pressure should be good, if not the inlet valve is bad or there is dirt in the filter. Also check the flow at the inlet of the water line. Once the water comes into the system the WATER LEVEL SENSOR - normally a pressure switch- must activate at the preset/chosen level to give the signal to the program controller to switch on the motor. What is most important for the motor to start functioning is that the door switch must be ON when the door is shut or this will be an error for starting the motor for rinse and wash.

Test a pressure switch: Click on : http://www.youtube.com/watch?v=HZZ2bDMspj8

Check this link to replace the inlet valve:

http://www.espares.co.uk/advice/washing-machines/a/7/1408/how-to-replace-the-inlet-valve-on-a-washer-dr.html

Finally after the wash the drain valve will be activated, the water is allowed to come in to rinse and then finally the dry spin with the drain valve/pump activated so as to drain off all the water from the clothes during the spin.

Make sure that a fault in any of the cycle will relate to the specified action, so check the command from the program module and then the executing device be it the valve or motor or pump.

Please check the link below:

http://www.repairclinic.com/Washing-Machine-Troubleshooting?red=Washing-Machine-Repair-Help

When the machine is on, but not running, press and hold the "pre-wash" button. After a few seconds it will begin that beep noise, keep holding it in until the beep volume goes down and finally stops. Once the beep has stopped, release the button and voila, no more annoying beeps at the end of your cycle.

To restore the end of cycle notification (beep) do the same thing as described above, but release the button earlier while the beep is still going.

check for blockages in the outlet pipes, filter and pump.

F21 normally indicates a fault with the motor or the main control board. It could be the motor brushes need changing. If you've changed the brushes you now need to erase the stored errors and try the machine again. . Turn the knob to off. Close the door. Turn the knob to 6 o'clock position. Wait 2 seconds. The start/pause should begin flashing. Press and hold the spin button. (the spin button is the one that changes the spin speed, it may be marked "RPM") Turn the knob to 7 o'clock position. Wait 2 seconds. Release the button. Turn the knob to off. . This should erase the error code and get you running again. . If the error code returns, you have a problem with the motor, wiring or main control. If the machine won't go into diagnostics to erase the error code, it would suggest a faulty control board. . Try it several times to see if you get it reset. . Note, If the start button doesn't flash, just carry on trying to erase the codes.

I have this completely SOLVED, what you need to do is:- Remove the drawer and look inside the drawer slot, at the top you will see loads of holes, in the middle you will notice a peice just above the fabric possition approx 2.5 inches long and 1 inch wide, It will have little clips either side. IT IS THIS PART THAT IS BLOCKED WITH GUNDGE!...You need to prize these clips apart and the middle bit will drop down and you can clean all the **** from it and you will of solved the problem. If you break the piece off dont worry because it will still clip back in place and function as it should. NO NEED to revove the top and clean the pipes. THIS IS THE SOLUTION...NO OTHERS WILL WORK!!!