20 Most Recent Proform Crosswalk 500 Treadmill - Page 4 Questions & Answers

You have electrical and electronic problems +mechanical:1) 1step: Watch this videos and make adjustment for electronics +electrical: http://www.youtube.com/watch?NR=1&v=USSgbsZbDLQhttp://www.youtube.com/watch?v=hKbAqvuOBS0&feature=relatedhttp://www.youtube.com/watch?NR=1&v=KiEZDNe0F8Qhttp://www.youtube.com/watch?v=wjrVjYe2LYQ&feature=relatedhttp://www.youtube.com/watch?v=CuMjcPLYehw&feature=relatedhttp://www.youtube.com/watch?v=yX_0vRPdMfU&feature=relatedhttp://www.youtube.com/watch?v=zXeHMWTcLUY&feature=relatedhttp://www.youtube.com/watch?v=dxpOOPetVLoGood luck, sincerely. G-d bless you.E.CUADRAMANAGUA, NICARAGUA. C.A.

Watch this videos tips:http://www.youtube.com/watch?v=qgb2TY3WCkg&feature=relatedhttp://www.youtube.com/watch?v=-oeXTKqWECw&feature=relatedhttp://www.youtube.com/watch?v=GPI6dFJCUA4http://www.youtube.com/watch?v=bF3OyQ3HwfU&feature=relatedhttp://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnesshttp://www.fixya.com/support/r10786838-test_procedure_dc_motor

http://www.youtube.com/watch?v=23ZgWaVEQjATest the speed sensor : if there is faulty replace it

If the console takes batteries, replace them. If this does not work or your console does not require batteries, check the reed switch or optic sensor. Reed Switch: Unplug the treadmill and remove the motor hood cover. The reed switch is mounted on the frame next to the front roller pulley. There is a magnet glued into the front roller pulley. When adjusting the reed switch, make sure it is pointing directly at the magnet. Move the tip of the reed switch within 1/8" of the magnet. Also, check to see that the wire is not damaged, and is connected to the console. Optic Sensor: Unplug the treadmill and remove the motor hood cover. The optic disk and sensor are located either at the end of the motor or the right hand side of the front roller. The optic disk spins between two sensors on the optic switch. The disk must spin freely without touching either sensor. The sensors can be moved by loosening the adjustment bolt holding the switch to its bracket. The switch can then be slid. Center the diskaFTER YOU TEST THE SENSOR DETERMINE IF THERE ARE FAULTY AND REPLACE.

This condition is when the treadmill operates normally without a person on the belt and then slows down when someone steps on the

belt or when the treadmill operates normally for a given period of time

with someone on the belt then abruptly begins to slow down.

There are four typical causes for this problem (listed in order of our experience:

1) The walking belt and/or deck are worn. (85% of the time)

2) The walking belt and/or motor belt are too tight- if you have adjusted either recently. (8% of the time)

3) The motor has lost torque and needs brushes or has demagnetized. (5% of the time)4) The controller is dropping output. (2% of the timeTest every step.http://www.youtube.com/watch?v=38w4PkiWIBY&feature=relatedhttp://www.youtube.com/watch?v=-oeXTKqWECw&feature=relatedhttp://www.youtube.com/watch?v=GPI6dFJCUA4

http://www.youtube.com/watch?v=hKbAqvuOBS0&feature=relatedhttp://www.youtube.com/watch?v=9o4cI10G_GA&feature=relatedhttp://www.youtube.com/watch?v=E5aWisfhT3Q&feature=relatedhttp://www.youtube.com/watch?v=38w4PkiWIBY&feature=relatedDo with pacience and carefully. sincerely.

Please go to the : www. proform. com and then customer service then parts& manual give your model and serial number and download free and ready.sincerely.

http://www.youtube.com/watch?NR=1&v=USSgbsZbDLQhttp://www.youtube.com/watch?NR=1&v=KiEZDNe0F8Qhttp://www.youtube.com/watch?v=wjrVjYe2LYQ&feature=relatedhttp://www.youtube.com/watch?v=yX_0vRPdMfU&feature=relatedhttp://www.youtube.com/watch?v=hKbAqvuOBS0&feature=relatedOf course after you did step and the problem persist, you must test the main motor complete, mechanical and electrical trouble.sincerely.

YOU CAN GO www . proform. com then go customer service and then parts& manuals give you serial number and model and download free your user manuals.However i wil give you some steps:http://www.youtube.com/watch?v=yX_0vRPdMfU&feature=relatedhttp://www.youtube.com/watch?v=38w4PkiWIBY&feature=relatedhttp://www.youtube.com/watch?NR=1&v=USSgbsZbDLQ

1) ADJUST REED SWITCH AND OPTIC DISK , AFTER YOU DID IF THE PROBLEM PERSIST. CHANGE IT.2) AFTER YOU DID, THE PROBLEM IS CONSOLE BOARD.TIGHT EVERY CONNECTION BETWEEN CONSOLE BOARD AND CONTROLLER BOARD, LOOSE CONNECTION, BAD CONTACT,CLEAN CONTACT SPECIAL SPRAY CONTACT CLEANER,

Watch this videos tips:http://www.youtube.com/watch?v=qgb2TY3WCkg&feature=relatedhttp://www.youtube.com/watch?v=-oeXTKqWECw&feature=relatedhttp://www.youtube.com/watch?v=GPI6dFJCUA4http://www.youtube.com/watch?v=bF3OyQ3HwfU&feature=relatedhttp://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnesshttp://www.fixya.com/support/r10786838-test_procedure_dc_motor

http://www.youtube.com/watch?v=23ZgWaVEQjAOf course check every connections loose, corroded, bad contact, tight, and clean every contact with special spray ( cleaner contact)

ADJUST 1) Reed swithc and optic disk.If after you did these adjustments Not work, replace the sensors.

Watch this videos and follow the step carefully.

Watch this videos tips:http://www.youtube.com/watch?v=qgb2TY3WCkg&feature=relatedhttp://www.youtube.com/watch?v=-oeXTKqWECw&feature=relatedhttp://www.youtube.com/watch?v=GPI6dFJCUA4http://www.youtube.com/watch?v=bF3OyQ3HwfU&feature=relatedhttp://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnesshttp://www.fixya.com/support/r10786838-test_procedure_dc_motor

http://www.youtube.com/watch?v=23ZgWaVEQjAOBSERVE THE BELT DRIVE MOTOR , very important, maybe is crack, or loose or faulty.

Observe carefully and follow the step:http://www.youtube.com/watch?v=N6Yg5S0WML8&NR=1http://www.youtube.com/watch?v=bF3OyQ3HwfU&feature=relatedhttp://www.youtube.com/watch?v=yX_0vRPdMfU&feature=relatedOf course you must shure the breaker from your house is Not Tripped, reset anywayand test it.

1) I do not recommend to do this. because you must bypass the electronic circuit and you can damage many ICS. if you do not have knowledge in electronic digital. Remember the treadmill fitness is very High Tech machine delicated.2) will be better go to www. proform.com go to customer service and then parts & manual and order the parts, the best solution.sincerely.

1) Retight the cable connector between the console and controller board, and clean it.2) Adjust the Reed switch and Optic sensor and determine if faulty, before the LCD is faulty.Finally after I you did check all step, the problem will be LCD faulty replace it.

If the console takes batteries, replace them. If this does not work or your console does not require batteries, check the reed switch or optic sensor. Reed Switch: Unplug the treadmill and remove the motor hood cover. The reed switch is mounted on the frame next to the front roller pulley. There is a magnet glued into the front roller pulley. When adjusting the reed switch, make sure it is pointing directly at the magnet. Move the tip of the reed switch within 1/8" of the magnet. Also, check to see that the wire is not damaged, and is connected to the console. Optic Sensor: Unplug the treadmill and remove the motor hood cover. The optic disk and sensor are located either at the end of the motor or the right hand side of the front roller. The optic disk spins between two sensors on the optic switch. The disk must spin freely without touching either sensor. The sensors can be moved by loosening the adjustment bolt holding the switch to its bracket. The switch can then be slid. Center the disk. FINALLY TEST THE SENSOR IF THERE ARE FAULTY AND REPLACE IT

Watch this videos tips:http://www.youtube.com/watch?v=qgb2TY3WCkg&feature=relatedhttp://www.youtube.com/watch?v=-oeXTKqWECw&feature=relatedhttp://www.youtube.com/watch?v=GPI6dFJCUA4http://www.youtube.com/watch?v=bF3OyQ3HwfU&feature=relatedhttp://www.fixya.com/support/r10724803-measure_voltage_in_transforme_fitnesshttp://www.fixya.com/support/r10786838-test_procedure_dc_motor

http://www.youtube.com/watch?v=23ZgWaVEQjATest very well the controller motor +main motor+Transformer, of course loose cables, bad contact, corroded cables or contact. Tight everything and clean for dust.

http://www.youtube.com/watch?v=N6Yg5S0WML8&NR=1http://www.youtube.com/watch?v=bF3OyQ3HwfU&feature=relatedhttp://www.youtube.com/watch?v=yX_0vRPdMfU&feature=relatedDo this first. if the problem persist check the:Reed switch +Optic sensor.