20 Most Recent
Sharp EL2196BL Printing Calculator - 12 Characters - Fluorescent - Power A - Page 4 Questions & Answers
My sharp ar 5320 is showing paper misfeed sign and it pointing at the heater unit side but ther is no paper there brushed all the sensors but its still showing the same
If your Sharp AR 5320 is showing a paper misfeed sign and it is pointing at the heater unit side but there is no paper there, it is possible that there is a problem with the sensors or other components inside the printer.
Here are some steps you can try to resolve the issue:
Turn off the printer and unplug it from the power source. Wait for a few minutes and then plug it back in and turn it on again. This can help reset the printer and clear any temporary issues.
Open the printer cover and check for any paper jammed inside the printer. If you find any, carefully remove it without tearing it.
Check the paper tray and make sure it is properly loaded with the correct size and type of paper. Adjust the guides to ensure they are holding the paper in place.
Clean the rollers and other parts of the printer using a soft, lint-free cloth. Dust and debris can accumulate over time and cause problems.
Check the sensors inside the printer to make sure they are clean and functioning properly. You may need to consult the printer's manual for instructions on how to access and clean the sensors.
If none of these steps resolve the issue, it is possible that there is a hardware problem with the printer. In that case, you may need to contact a qualified technician for assistance or consider replacing the printer.
My sharp AR5618D is not printing after commanding print on a laptop. what should i do for it to print?
There could be a few issues that could be causing your Sharp AR-5618D printer to not print after commanding a print job from your laptop. Here are some troubleshooting steps you can try:
- Make sure that the printer is turned on and connected to the same network as your laptop.
- Check to see if there are any error messages displayed on the printer's control panel. If there are, try to resolve the issue based on the error message.
- Check to see if there is paper in the printer and if it is properly loaded.
- Check to see if the printer is out of toner or ink and replace it if necessary.
- Try printing a test page from the printer's control panel to see if the issue is with the printer or the connection between the laptop and the printer.
- If you are using a USB cable to connect the printer to the laptop, try a different cable or a different USB port on the laptop.
- Check to see if there are any updates available for the printer's driver and firmware and install them if necessary.
- If none of the above steps help, try uninstalling and reinstalling the printer driver on your laptop.
I hope these suggestions help! If you continue to have issues, it may be helpful to consult the printer's manual or contact the manufacturer for further assistance.
My Sharp photo copier AR-5316 is showing e7 error what causes this errors?
The E7 error on the Sharp AR-5316 is an indication that toner has run out. This can occur if the machine has been left idle for a long period of time and the toner has settled at the bottom of the toner bottle. To resolve this, replenish the toner, remove and reseat the toner bottle, and then reset the machine.
How do I correct error U2-40 on Sharp AR-M236
Hi,
U2-40 is the error code for the toner cartridge.
It indicates a fault with the chip in the cartridge.
Try entering simulation mode to reset the error first, to do this make sure the machine is in COPY mode.
Then press the following 4 keys in order: #*C*
then enter 16 & press the copy start key.
Then follow the instructions on the screen to reset U2 error.
When complete, press CA key to exit simulation mode.
If the error re-occurs then the toner cartridge will have to be replaced & the machine reset again as above.
Hope this helps.
Dave.
Sharp mx-m623n error u2-81
Dear sir; This error code means "scanner memory" problem, don't worry, we can reset it, the procedure as follow;
1, make sure you are in copy mode , then press "p", "*", "clear", "*".
2, enter 16 press start.
3, press "CA" to end simulation.
Not finding what you are looking for?