20 Most Recent Hoover Elite Rewind Bagless Upright, UH71009 - Page 5 Questions & Answers

Part 26 https://evacuumstore.com/s-1587-u6425-900.aspx https://www.google.com/search?q=Hoover+wind+tunnel+parts+schematic ..

Yes, they are everywhere including Walmart and eBay.

Replacement for Hoover Windtunnel UH70400 Brush Roller ...

https://www.amazon.ca > UH70400-Windtunnel-Engin...

Replacement for Hoover Windtunnel UH70400 Brush Roller Fits UH70400 Air Bagless Upright, Compatible with Part # 303792001, by Think Crucial: ... Rating: 4.1 · ‎33 reviews

Hoover UH70400 Wind Tunnel Air Brushroll Assembly ...

https://www.amazon.ca > Hoover-UH70400-Tunnel-Br...

Hoover UH70400 Wind Tunnel Air Brushroll Assembly: Amazon.ca: Home & Kitchen.

Replacement Brush Roller, Fits Hoover UH70400 Windtunnel ...

https://www.thinkcrucial.ca > products > hoover-uh704...

Replacement Brush Roller, Fits Hoover UH70400 Windtunnel Air Bagless ... A brush roller on your vacuum is really like a broom for your carpet, that gets all the ... HUNDREDS here! https://www.google.com/search?q=brush+roll+for+hoover+uh70400 ..

check you tube

Turn it over when open up and run it. Use the pads of your fingers to try and sop the brush. DON'T stick your fingers in it! All you are trying to do is see if resistance will stop the brush turning. If that passes the test, and the most likely cause is that you have a suction issue. You need to check all the airways from the top of the brush to the waste canister. The canister must also be a good seal. I had one of them and got rid of it for a Dyson.

https://www.weeklytools.com/5-best-cordless-pressure-washers-buying-guide/ Looking for the most effective and powerful home appliance to give you a hand with all the cleaning tasks? Cordless pressure washers are just the thing you have been waiting for. This great and affordable cleaning tool is constructed in a compact shape and is built to generate enough pressure that allows deep cleaning for various surfaces. The best part? It runs entirely on battery and does not require any power outlet to operate. Although there are many options to pick from, some important features separate the best battery operated pressure washers from the others.

The new thermal fuse must be crimped into place exactly as the old one is.

check the shaft ends for hair that has wound tight a dental pick worked well for me

CONTACT HOOVER DIRECTLY

Try testing plug and switch and their is no fuse

Contact Hoover directly to request the diagram.

Assuming the motor and blower (that creates the suction) are working the most likely reason is a loose cover (lid) on the recovery tank. Also, check the seam where the lid meets the tank and clean any debris that might prevent a good seal. Be sure the small, black gasket in the lid is intact with no tears or gaps.

New brushes/motor will fix it perhaps.

Reduction or loss of suction power could be caused by several things, including a blockage in the water channel, the water channel hose, recovery hose (located behind the recovery water tank), deteriorating rubber seals, dirty/clogged filter, dirty louver cover (exhaust for the vacuum above the tank).

FLOORMATE Floor Cleaner Repair

..

if water pump working possible clogged hose or spray jets

The replacement belt might not be a genuine Hoover part. A slight difference in circumference could allow slippage. Also, the brush roller bearings could be clogged with debris which would cause the drive belt to slip.

Finds the cracked or leaking part and replace it. Full parts schematic here https://www.usavacuum.com/Hoover-F5883-SteamVac-Upright-Extractor-Parts-s/817.htm Or take it in for service and repair.

If you can hear the motor running it probably needs a new drive belt and if the motor isn't running there is an electrical fault that must be checked by a suitably experienced person. Some of the older power scrubbers/polishers I have seen didn't have a belt but used a simple but substantial gear drive system that gave no trouble in my experience.

The part number you provided returns no results by google and doesn't appear in the parts list of the model. You will have to do more research or provide a long-hand description...

~It appears to be a known issue with that model. Find the leak and fix the crack with JB Weld. https://www.thriftyfun.com/Hoover-Carpet-Shampooer-Dumping-Water.html ..

The switches may have been cheap substitutes for the genuine Hoover part.