Top 20 Remote Start System Questions & Answers

notify viper to troubleshoot

I think you need to buy a new starter buddy if it won't engage you're going to need a new starter there's really no way around that but once you get a new starter you should be fine they're not too expensive

There's a website that ha s all this information about all this and manuals everything totally free there are many actually but I personally like few .. let me know if u need help thanks

have you tried changing the battery? also does the central locking work by the key or inside the car button?

If it backfired it's quite often timing. I don't know what motor you have but see if you can check the timing. If it's not the timing check if the car has a camshaft and or crankshaft sensor. If one of those go bad she wont start. Another quick test is to spray starting fluid or some carb cleaner into the intake and swing it over ... if it starts you have a fuel issue. Maybe the pump.

Glow Plug lol thats a remote l (more Info )

I take help from online websites that have this service like helping in repair some like reliable-store have instant help.. others are a bit slow which I don't prefer... rest is up to u.. U get free manuals

Remove the remote starter it is not oem.

Avital and viper remotes even though they look the same, they operate at different freqs. Im a retired alarm installer i could never get them to interchange.

hello u will find a lot of wiring diagrams, codes etc and circuit diagrams help books and stuff like this at online places.. like reliable-store for free the girl in the chat box can help u instantly... im a frequent buyer there since Im a mechanic so take help from there

problem is the low battery have it load tested and charged up or replaced remote or key still use the same bad battery

Consider how the switch will be used before choosing a mounting location. Check for rear clearance before drilling a 9/32-inch hole and mounting the switch.The GRAY wire in the two-pin plug may also be used as a (+) ghost switch input and can be connected to any (+) switch in the vehicle. (See Feature Descriptions section of this guide.) This is from the installation manual for the Viper 300. To answer your question, it is probably camoflaged. They only needed to tie +12vdc to the input line. What does this mean? Well, my best guess is, they are using one of your switches on your dash to act as the Valet function. Look for where the Gray wire, from the wiring harness of the Viper goes to: that WILL BE your hidden Valet switch. Best of luck! Viper 300 ESP Installation Manual Plug in Harnesses Super Bright Led Valet...

Lock the driver side door then open it with key that might reset you anti thief to your remote.

I got this free Pdf manual from reliable-store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of all the times I fixed the chipper in these 4 years

here's the manual https://www.directeddealers.com/manuals/OG/Viper/G4806V%202013-06%20web2.pdf

It says its a Viper alarm system. . If the alarm system is active, reprogramming the ignition keys was a waste of money. The problem is in the control box for the viper alarm system. It has disabled the ignition because it thinks that is being broken into. there are sensors that monitor the the vehicles vibration and is probably a problem with one of the sensors or maybe even the control box itself.

You need to re-program the TACH wire.. open the door start the car with the key, between 5 seconds press the valet switch 1 time and press it again and hold it until the led flashes and the car will beep and then turn it off and start the car with the remote and it should be programed now. if that doesn't work take it to a authorized viper dealer to have it fixed.

son muchos cables los ke tienes ke unir asi es ke te recomiendo ke lo lleves a aun lugar dodnde hagan instalaciones te va salir mas barato pagar para ke te lo intalen ke cometer un error y tener ke pagar para repararla

I got this free Pdf manual from an online store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of the all the times I fixed the chipper in these 4 years

hi no your car alarm wont effect the tire pressure but if you have no problem with your car alarm its not your car alarm causing the problems its the dealer not wanting to honor the warranty by making up excuses if your car is covered by the warranty they sold you the car with alarm already installed so they are still liable i guarantee that warranty never said not covered by the warranty because of an after market car alarm installed take the car back and order them to fix the problems because its under warranty and they sold you the car with the car alarm so thats there problem not yours Take a male friend with you if you feel abit over whelmed as they try to take advantage of everyone and he can speak on your behalf and offer you supportcheers