http://www.fixya.com/support/browse/vacuumsSolved technical support problems provided by FixYa users.en-usCopyright (c) 2007 FixYa, LTD. All rights reserved.info@fixya.comWed, 06 Jan 2010 01:22:17 GMT80http://www.fixya.com/support/t3762549-beater_bar_not_turn_belt_fineThe beater bar does not turn. The belt is fine. I had the same problem before, sent to Dyson, and they fixed. Same problem again, called Dyson, sorry can't fix again free. Dang. I suspect the switch that turns the beater bar on and off.Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3729454-vacuuming_pulled_up_throw_rubso i was vacuuming and pulled up a throw rub for about 10 seconds or less. i turned off the vacuum and and now the brushes wont spin. what do you think i should do? Thanks TommyWed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3700832-checked_machine_blockages_noneI have checked the machine for blockages, none found.However, the machines turns off after running for about one minute. Any ideas?Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3694587-will_not_steamwill not steamWed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3691730-re_proheat_protech_model_no_sprayRe. Proheat / Protech model No spray happens, I have made sure both the water bag is full & the cleaning fluid are both fully located, the water does seem to be getting into the carrier without having been sprayed.Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3665783-water_doesnt_despencewater doesn't despenceWed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3663112-v_belt_loose_brush_switchThe V belt is too loose. The brush switch actuator does not appear to be putting enough tension on the V belt. The roller brush does not spin because the belt is too loose. I changed the belt with no improvement. What can I do to fix this problem?Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3646628-steam_in_hover_steamvacWhere is the STEAM in the Hover SteamVac F5914-900??Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3620723-eureka_boss_smartvac_model_4870_rollerMy Eureka The boss Smartvac Model #4870 roller brush won't turn even on the highest setting and the belt smells hot. we took the belt off. How can you tell if it needs replaced?Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3619896-change_belt_seem_remove_bottomHOW DO YOU CHANGE BELT CANT SEEM TO REMOVE BOTTOM TO GET TO IT KENMORE WISPERTONE 116Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3615980-bissell_2xswater not coming out of machine, but comes out of hose when pressed. Plz help??????????ThanksWed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3606960-need_parts_list_kirby_3I am missing some parts on my Kirby 3 and would like a parts break down list.Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3596554-will_not_cyclone_any_more_brush_bottonwill not cyclone any more. brush on botton will not spin.Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3589812-water_not_being_dischargedwater is not being discharged. I have filled the reservoir that holds the carpet cleaner fluid And I have filled the water container. I know how to use the cleaner, it has always worked, But now, no water is being discharged to the carpet. I turn...Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3574602-older_dyson_07_animal_loud_ratchetingThis older model works only with the FLOOR setting (manual switch at bottom). When switching to the CARPET setting, a loud ratcheting noise happens and sounds terrible. The brush bar is clean. The sound I hear appears to be in the hidden area above...Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3560676-download_manual_ultimate_g_kirbywhere can i download a manual for ultimate g kirby vacWed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3558110-change_belt_in_hooverhow do I change the ******** belt in a Hoover Empower upright vacuum?Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3539063-when_start_scrub_water_comes_out_butwhen you start to scrub the water comes out but the brushes wont turn and there is very little suctionWed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3526738-hoover_steam_vac_model_f7425this is a 6 brush model, the brushes do not rotate, the filter is clean and the switch is in the on positionWed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3526263-soap_solution_valve_wand_not_workingThe valve to dispense the soap solution on our little green machine is not working, can I get a better valve? The machine also seems to plug up frequently where the soap solution exits the wand in that little hole. Is there a fix for that?Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3510064-need_replace_vacuum_belt_eureka_modelneed to replace a vacuum belt on a eureka model 4377. I cannot figure out how to remove the bottom portion to get to it.Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3487956-dirt_not_spin_dirt_dificultthe dirt does not spin and dirt is dificult to pick upWed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3477921-swivel_sweeper_battery_pack_apartCan you take the Swivel Sweeper battery pack apart to replace the batteries with new rechargeable batteries? Batteries look like AA or AAA, but it appears that the battery pack is sealed. Is there any way to get it apart:?Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3458161-rotary_brush_stopped_spinning_believeThe rotary brush stopped spinning. I believe its something to do with the belt... but I don't know how to check.. I've had it for less than 60 daysWed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3451295-replace_belt_kenmore_canisterHow do I replace the belt on my Kenmore canister vacuum?Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3449809-no_power_when_flip_start_switch_or_iino power when i flip the start switch to I or II? Is there a reset button?Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3435133-brush_doesnt_turn_when_machine_runningThe brush doesn't turn when the machine is runningWed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3430754-brushes_stopped_spinning_altogetherThe brushes have stopped spinning altogether unless I manually reach it and turn them every 30 seconds.Wed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3424331-when_turn_vacuum_s_blowing_air_out_noWhen I turn on the vacuum it's blowing air out no suctionWed, 06 Jan 2010 01:22:17 GMThttp://www.fixya.com/support/t3421924-get_belt_dc24How do I get to the belt on my DC24?Wed, 06 Jan 2010 01:22:17 GMT