Question about Fleetwood 2014 Storm 28F

1 Answer

What is the problem, my Storm is plugged into the power supply and everything does not work until I start it up. When I turn it off, the lights and everything else works for a little while then sarts to dim and go off.

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 405 Answers

Do you have power at the outlets? If you do but the lights keep going dim then your converter is going bad or has already failed. Your lights are 12v and the outlets are 100v. If you do not have power at the outlets then you need to check the transfer switch that toggles between generator power and shore power.

Posted on Jul 24, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a 2001 presidential 5th wheel it is hooked up and plugged and everything works but the lights. Is there a separate switch to turn these on?


There is probably a breaker box in the bedroom closet behind a panel. Look elsewhere if not there and check the breakers when you find it. You may have a short circuit somewhere and the breaker opened. Or maybe even a failed breaker. Check for voltage at the breaker itself. Don't assume the breaker is getting power.

Feb 03, 2017 | Holiday Rambler 2010 Presidential 36RET

1 Answer

Dont have power on lights when trailer is plugged in to ac current on my 2008 sandpiper rv


The most common problem is blown main fuses on the power unit which blow when you operate or try to operate the slides with low batteries and the power supply not connected to the landline power source.

Jan 27, 2017 | RVs

1 Answer

How to winterize


ok, been a while so lets ee if I can get this all down.

1 - Drain water from your holding tank and remove drain plug in hot water heater. Drain holding tanks ( Waste )
2- turn on bypass for hot water heater ( instruction if needed )
3 - Get yourself some winterizing fluid ( can't remember exact name ) from your local Dealer . 2 or 3 gallons should be good
4- Poor this fluid into your water rez tank. All of it
5 - now go around to EVERY tap in your trailer ( one at a time ) and turn on cold water until water runs pink ( or what ever colour fluid you bought ) Close faucet them do the same for hot water tap. Repeat this at every faucet. Even the ones outside if you have any.
6 Don't forget to flush toilet in water runs pink.
7. Ensure all gas vales have been turned off ( tank vales included )

If you did everything right you should be good to go.

Plz double this list to make sure I covered everything

Oct 02, 2016 | Keystone 2015 Alpine 3555RL

2 Answers

Hot water heater went out. Can't relight


check that there is gas in the bottle , the tap is on
check that there is power to the relight system

Oct 25, 2015 | Dutchmen 2011 Coleman 387DQDS

1 Answer

Can you turn on the hot water pilot light if water is frozen


No it shouldn't hurt anything, the damage may already be done. I would first turn off the water supply to the heater, and attach a hose to the drain and open it. Lighting the pilot will help the unit thaw. Once you feel it has completely thawed and drained, close the boiler drain and open the supply slowly to check for leakage before full use.
Good Luck

Mar 06, 2015 | Keystone 2015 Springdale 190SRTWE

1 Answer

Is there a youtube video replacing analog with lcddometic ctrl kit 3313189.000


Not that I am aware of but it is pretty straight forward. First, turn off the breaker to the AC. Then uplug the upper unit from the control box, Then disconnect the 110vac from the box, and then clip the thermostat wires. There will be, typically colored blue, two wires which go to your furnace, a ground wire and a 12vdc hot wire. The two blue wires will get the insulated female spade terminals installed so that they can be directly plugged into the new control box. The 110vac will wire into the new box the same as it was in the old box. The upper AC harness will plug directly into the new box and the new freeze control will plug directly into the new box and the yellow card will show you where to install it into the coils for the best results. You will receive a new harness that will supply power to the thermostat. Each wire is identified with a label and there is also a schematic on the inside lid of the new control box. Pick three wires from the thermostat wires and write down which one you assign to be neg, pos and comm. Wire the new harness with 12vdc + input to the 12vdc + supply. Wire the 12vdc - and the thermostat - to the 12vdc - supply. Wire the 12vdc + (Therm) to the wire that you have selected to be the positive wire to your thermostat and then connect the communication wire to the wire that you have selected to be the comm wire. Now, install the new thermostat on the wall with the three wires pulled through the small oval hole at the top. There will be three blue block terminals with small regular slotted screws in them. Each one is appropriately marked +, -, comm. Attach each wire that you have chosen accordingly. Once everything is wired in and secured turn the power back on and you should have a readout on the LCD display. You may have to hold the + and mode buttons until you get a - - which will program the thermostat for degrees Celsius. Now set the fan mode to AU and then adjust your cool temp. If you turn the furnace on in the winter time and the ac fan starts blowing go back to your fan setting and change it to AU. If it is set to LO or HI the AC fan will come on when the furnace is turned on. Have Fun!

May 18, 2014 | RVs

1 Answer

What is the problem, my Storm is plugged into the power supply and everything does not work until I start it up. When I turn it off, the lights and everything else works for a little while then sarts to...


There may be a number of reasons for this. If you are running an air conditioner, the compressor could be stuck or going bad and dropping the voltage. Also, there could be a problem with the refrigerator compressor. If you have a battery bank, there could be a problem with the charging system for the batteries. Try eliminating the frig and the air conditioner first. Then check the battery bank to see if the batteries have a short. The charging system itself could be causing the drop in voltage also. Only by checking one thing at a time will you solve this problem. I have seen people use a power cord that is too light duty and this can cause the same problem.

May 09, 2014 | Fleetwood 2014 Storm 28F

2 Answers

Battery/elecrtic


You might unhook the battery and with the camper plugged in to shore power the 12v lights should work. If not check the breaker that goes to the inverter. If that is not tripped then check the power output at the converter. I would expect the inverter is shot. I replaced the one on my Jaco two years ago with (Progressive Dynamics 60 Amp Power Converter with Charge Wizard and the remote pendant)

Apr 02, 2014 | Jayco 2010 Jay Feather SPORT 165

1 Answer

No power on Cyclone 4100


Do you have power at the outlet where the unit is plugged in? If not restore power to that point. Next, check the main breaker to determine if it has tripped. It may look like it is on but to verify, turn it off and then back on. It should click into place. If that does not work and your trailer has a genset with a transfer switch. Check the transfer switch to make sure that it has not failed. It may be locked into the genset side and not switching back to shore power. If you are running the genset and do not have power make sure the breakers on the front of the genset are on.

Mar 02, 2014 | Heartland 2012 Cyclone 4100 KING

Not finding what you are looking for?
Fleetwood 2014 Storm 28F Logo

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fleetwood RVs Experts

keylempi

Level 1 Expert

38 Answers

L Pfaff
L Pfaff

Level 3 Expert

11573 Answers

Jerry Kramer
Jerry Kramer

Level 3 Expert

3904 Answers

Are you a Fleetwood RVs Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...