Question about Harley Davidson FLHT Electra Glide Standard Motorcycles

1 Answer

How do I remove the ignition key cap off of a 2000 Electraglide standard, thereis no button on the bottom.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

I wouldn't try messing with removing the ignition switch. It takes a special tool to get it back together if you get the layers out of time with each other.

Good Luck
steve

Posted on May 30, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key stuck in da ignition how can i remove it


if its a standard type key, you most likely have an issue with the shift interlock. the shifter must be in park in order to remove key. if the interlock switch goes bad, the key will not come out of ignition.try pushing forward on shifter while trying to remove key.

Jun 30, 2012 | 2000 Volkswagen Beetle

1 Answer

Fork lock locked up won't unlock


I don't know if this will help. It was sent to me by a friend of mine and I've never tried the procedure. I do not work on these ignition switches and fork locks. This is for a newer model but it may help. Good Luck. Steve

Here's the procedure to remove the IGNITION /LIGHT KEY SWITCH AND FORK LOCK for a 2005 FLHT/C/U or FLTR (Domestic): Tools needed for removing ignition switch A T27 Torx, a small flat blade screwdriver, 7/8 wrench.

1. Remove the outer fairing and windshield

2. To remove the ignition switch, insert the ignition switch key and turn to the UNLOCK position. Leaving the key installed, rotate the knob to ACCESS. Depressing the release button at bottom (left side) with a small screwdriver, push key down and turn an additional 60 degrees in a counter-clockwise direction. Lift and remove knob.

3. Using a 7/8 wrench on flats, loosen switch nut and remove from threaded post of ignition switch housing. Remove collar and spacer.

4. Using a T27 TORX drive head, remove the two screws (with flat washers) that secure fairing cap to left and right sides of fairing.

5. Remove the switch position plate by pulling tabs from slots in faring cap. If necessary, raise the fairing cap slightly to facilitate removal.

6. With the forks turned fully to the left, disconnect the Fairing cap switch connector (105) 12-place Multilock (black), from behind right side of fairing cap. Depress the button on the plus side of the connector to pull apart the pin and socket halves.

7. Remove the fairing cap from the motorcycle.

8. Locate the ignition switch connector (33), 4-place Packard, at bottom of radio. Slide connector off anchor and separate pin and socket halves.
9. Remove the socket screws (with flat washers) and lift the switch housing from the upper fork bracket bore. Route the ignition switch connector to rear of inner fairing and remove switch housing from the vehicle.

Sep 19, 2011 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

Flhtcui key switch install, new out of the box


I've posted this before. I got this from a friend of mine and like I said before, I cannot attest to it's accuracy. I do not work on these types of ignition switchs. In the past, they required a special tool to align the switch that I didn't have. Anyway, this is what I have on the switch. I hope it works for you.

Good Luck
Steve

Here's the procedure to remove the IGNITION /LIGHT KEY SWITCH AND FORK LOCK for a 2005 FLHT/C/U or FLTR (Domestic): Tools needed for removing ignition switch A T27 Torx, a small flat blade screwdriver, 7/8 wrench.

1. Remove the outer fairing and windshield

2. To remove the ignition switch, insert the ignition switch key and turn to the UNLOCK position. Leaving the key installed, rotate the knob to ACCESS. Depressing the release button at bottom (left side) with a small screwdriver, push key down and turn an additional 60 degrees in a counter-clockwise direction. Lift and remove knob.

3. Using a 7/8 wrench on flats, loosen switch nut and remove from threaded post of ignition switch housing. Remove collar and spacer.

4. Using a T27 TORX drive head, remove the two screws (with flat washers) that secure fairing cap to left and right sides of fairing.

5. Remove the switch position plate by pulling tabs from slots in faring cap. If necessary, raise the fairing cap slightly to facilitate removal.

6. With the forks turned fully to the left, disconnect the Fairing cap switch connector (105) 12-place Multilock (black), from behind right side of fairing cap. Depress the button on the plus side of the connector to pull apart the pin and socket halves.

7. Remove the fairing cap from the motorcycle.

8. Locate the ignition switch connector (33), 4-place Packard, at bottom of radio. Slide connector off anchor and separate pin and socket halves.

9. Remove the socket screws (with flat washers) and lift the switch housing from the upper fork bracket bore. Route the ignition switch connector to rear of inner fairing and remove switch housing from the vehicle.

Sep 18, 2011 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

2005 FLHTCUI key switch replacement. Mitchell's Harley Davidson wrecked my bike. Last thing they did before I took it back was break the key switch.


I can't swear to the accuracy of these instructions as I don't mess with the later Twin Cam bikes. I work on the older Shoveheads, Panheads, and Ironhead Sportsters that the dealers won't work on. But, a friend sent this to me. Maybe it works. Good Luck.

Here's the procedure to remove the IGNITION /LIGHT KEY SWITCH AND FORK LOCK for a 2005 FLHT/C/U or FLTR (Domestic): Tools needed for removing ignition switch A T27 Torx, a small flat blade screwdriver, 7/8 wrench.

1. Remove the outer fairing and windshield

2. To remove the ignition switch, insert the ignition switch key and turn to the UNLOCK position. Leaving the key installed, rotate the knob to ACCESS. Depressing the release button at bottom (left side) with a small screwdriver, push key down and turn an additional 60 degrees in a counter-clockwise direction. Lift and remove knob.

3. Using a 7/8 wrench on flats, loosen switch nut and remove from threaded post of ignition switch housing. Remove collar and spacer.

4. Using a T27 TORX drive head, remove the two screws (with flat washers) that secure fairing cap to left and right sides of fairing.

5. Remove the switch position plate by pulling tabs from slots in faring cap. If necessary, raise the fairing cap slightly to facilitate removal.

6. With the forks turned fully to the left, disconnect the Fairing cap switch connector (105) 12-place Multilock (black), from behind right side of fairing cap. Depress the button on the plus side of the connector to pull apart the pin and socket halves.

7. Remove the fairing cap from the motorcycle.

8. Locate the ignition switch connector (33), 4-place Packard, at bottom of radio. Slide connector off anchor and separate pin and socket halves.
9. Remove the socket screws (with flat washers) and lift the switch housing from the upper fork bracket bore. Route the ignition switch connector to rear of inner fairing and remove switch housing from the vehicle.

Sep 03, 2011 | Harley Davidson FLHTCUI Electra Glide...

1 Answer

How to remove ignition switch on 2001 electra-glide


Here is something a friend sent to me. I've never taken one of these switches out so I can't say for sure if this is correct but it's all I have.

Here's the procedure to remove the IGNITION /LIGHT KEY SWITCH AND FORK LOCK for a 2005 FLHT/C/U or FLTR (Domestic): Tools needed for removing ignition switch A T27 Torx, a small flat blade screwdriver, 7/8 wrench.

1. Remove the outer fairing and windshield

2. To remove the ignition switch, insert the ignition switch key and turn to the UNLOCK position. Leaving the key installed, rotate the knob to ACCESS. Depressing the release button at bottom (left side) with a small screwdriver, push key down and turn an additional 60 degrees in a counter-clockwise direction. Lift and remove knob.

3. Using a 7/8 wrench on flats, loosen switch nut and remove from threaded post of ignition switch housing. Remove collar and spacer.

4. Using a T27 TORX drive head, remove the two screws (with flat washers) that secure fairing cap to left and right sides of fairing.

5. Remove the switch position plate by pulling tabs from slots in faring cap. If necessary, raise the fairing cap slightly to facilitate removal.

6. With the forks turned fully to the left, disconnect the Fairing cap switch connector (105) 12-place Multilock (black), from behind right side of fairing cap. Depress the button on the plus side of the connector to pull apart the pin and socket halves.

7. Remove the fairing cap from the motorcycle.

8. Locate the ignition switch connector (33), 4-place Packard, at bottom of radio. Slide connector off anchor and separate pin and socket halves.

9. Remove the socket screws (with flat washers) and lift the switch housing from the upper fork bracket bore. Route the ignition switch connector to rear of inner fairing and remove switch housing from the vehicle.

Sep 03, 2011 | 2001 Harley Davidson FLHTCUI Electra Glide...

2 Answers

I HAVE A BAD IGNITION SWITCH IN MY 1996 FLHP AND CANT FIGURE OUT HOW TO REMOVE HEAD OF SWITCH TO REMOVE AND REPLACE.


I have no experience with these types of ignition switches. Here's something that someone sent to me once. It may help you figure out how to work on your switch. I always avoided those switches as someone said that you had to have a special tool to reassemble the switch once you took it out. An alignment tool of some sort. So, I sent anyone with a problem with one to a shop that knew what they were doing. You may want to check with Harley Davidson Customer Service on that switch. Seems that there was a recall on the ignition switches on bikes built somewhere around the time your's was built. I think I ran into a '94 model that was covered under a recall. He took it to a dealer and they fixed it at no charge. If you call Harley, have your VIN number handy.


Good Luck

steve


Here's the procedure to remove the IGNITION /LIGHT KEY SWITCH AND FORK LOCK for a 2005 FLHT/C/U or FLTR (Domestic): Tools needed for removing ignition switch A T27 Torx, a small flat blade screwdriver, 7/8 wrench.

1. Remove the outer fairing and windshield

2. To remove the ignition switch, insert the ignition switch key and turn to the UNLOCK position. Leaving the key installed, rotate the knob to ACCESS. Depressing the release button at bottom (left side) with a small screwdriver, push key down and turn an additional 60 degrees in a counter-clockwise direction. Lift and remove knob.

3. Using a 7/8 wrench on flats, loosen switch nut and remove from threaded post of ignition switch housing. Remove collar and spacer.

4. Using a T27 TORX drive head, remove the two screws (with flat washers) that secure fairing cap to left and right sides of fairing.

5. Remove the switch position plate by pulling tabs from slots in faring cap. If necessary, raise the fairing cap slightly to facilitate removal.

6. With the forks turned fully to the left, disconnect the Fairing cap switch connector (105) 12-place Multilock (black), from behind right side of fairing cap. Depress the button on the plus side of the connector to pull apart the pin and socket halves.

7. Remove the fairing cap from the motorcycle.

8. Locate the ignition switch connector (33), 4-place Packard, at bottom of radio. Slide connector off anchor and separate pin and socket halves.

9. Remove the socket screws (with flat washers) and lift the switch housing from the upper fork bracket bore. Route the ignition switch connector to rear of inner fairing and remove switch housing from the vehicle.

Aug 23, 2011 | Harley Davidson Gypsy Motorcycles

1 Answer

Take ignition off


1.) Remove Dash
2.) Remove Fairing Cap
3.) Rotate forks to Forward facing Position.
4.) Turn ignition switch to lock position.
5.) Insert key
6.) Hold button in and push key down, rotating counter clockwise.
7.) The switch will pop straight up.
8.) Careful of the large spring that will drop from bottom of switch as you remove it.
9.) Use 7/8" open end wrench to loosen the nut on top of the cylinder.
10.) Remove plastic ring.
Take care that assembly occurs opposite of removal.

Feb 27, 2011 | 2005 Harley Davidson FLHT - FLHTI Electra...

1 Answer

How to remove the ignition switch


1.) Remove Dash
2.) Remove Fairing Cap
3.) Rotate forks to Forward facing Possition.
4.) Turn iginition switch to lock position.
5.) Insert key
6.) Hold button in and push key down, rotating counter clockwise.
7.) The switch will pop straight up.
8.) Careful of the large spring that will drop from botton of switch as you remove it.
9.) Use 7/8" open end wrench to loosen the nut on top of the cylinder.
10.) Remove plastic ring.
Take care that assembly occurs opposite of removal.

Jan 08, 2011 | 2005 Harley Davidson FLHT - FLHTI Electra...

1 Answer

Need help programing my keyless remote for a 2000 alero. This is what is on the back, GM/UTA 25665575, FCC ID. KOBUT1BT,Canada 1983 101 393 It has four buttons top two are left pic of lock, Right pic of...


1. Close the vehicle doors.

2. Turn ignition to the ON position then OFF.

3. Remove key from the ignition.

4. Press and hold the driver side door lock switch in the UNLOCK position
until step 8.

5. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

6. Insert the ignition key into the ignition lock cylinder and remove the key.
(Do not turn the ignition key in the lock cylinder)

7. Insert the ignition key into the ignition lock cylinder.
(Do not turn the ignition key in the lock cylinder)
Leave key in the ignition cylinder.

8. Release the door lock switch. The vehicle will sound three beeps in order
to verify the Program Mode has been activated.

9. Press the LOCK and UNLOCK buttons together on the keyless remote and
hold unitl the vehicle beeps twice to verify that the keyless remote has been
successfully programmed. This may take approximately 15 seconds.

10. Perform the previous step (9) to program up to four keyless remotesm, including
any old ones.

11. Remove the ignition key to exit Program Mode.



Thank you for using Fixya and good luck

Mar 17, 2010 | 2000 Oldsmobile Alero

1 Answer

How do you get the key ignition out of a 2000 ford focus?


there should be a button on the bottom of the column to release the key from the ignition ad put the ignition in the lock position

Jan 19, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76132 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...