Question about 2008 Harley Davidson FXD Dyna Super Glide

1 Answer

Four in-line 12v15amp breakers first one in line keeps clicking as if to shut down and all lights blink when it does this also no turn signals at all function otherwise bike runs fine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

This sounds like it's your "accessories" circuit breaker. The only way to tell is to look at a schematic of your bike. I'm sorry but I do not have schematics for bikes later than 1999. You'll have to find out what devices are on this circuit and disconnect the power wire from each one. As you reconnect the devices one at the time, listen for the circuit breaker to trip. When it does trip, you've found the problem.

Good Luck
Steve

Posted on May 29, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Leq2152ee1 dryer does dry but keeps stopping if put on any setting over 15 min. Dryer stops single beep and top four lights blink.


MAY BE BAD MOTOR WITH BAD WINDINGS USUALLY STOPS AFTER 20 MINUTES OF USE? OR HEATING ELEMENT IS OVERHEATING? DUE TO BAD VENTING? THERMAL CUT OFF KEEPS SHUTTING IT DOWN?

May 08, 2014 | Frigidaire GLEQ2152ES Electric Dryer

1 Answer

Kv 27542


  1. Four blinks - No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal muted. Check IC1509, Q1505

Jun 27, 2013 | Sony Televison & Video

1 Answer

Power light blinking on nv53a gateway


Your Gateway laptop comes with a series of LED lights that alert you to the state of your computer. You'll notice there are blue, purple and red lights that either blink or display solidly. Each light, blinking or solid, has a different meaning. The blue blinking light on your laptop indicates that it is in Standby mode. Your laptop goes into Standby when you close its lid without shutting down the computer. To turn this light off, you'll need to take the computer out of Standby mode, and if you want to ensure that the blinking blue light does not return, shut down the computer after each use.

Open the lid of your Gateway laptop and press the power button. Once Windows loads, enter your password if required. The blue light will no longer be blinking because the computer is no longer in Standby mode. Shut the laptop off when you finish using it rather than simply closing the lid to stop the blue light from blinking again. Click "Start" from your Windows desktop and click "Shut down." Change your computer's power settings to keep if from going into Standby mode when you close the lid if you'd rather not shut down your computer every time you use it. Click "Start" and click "Control Panel." Click "System and Security" and then click "Power Options." Click "Choose what closing the lid does" from the list of options on the left side of the window. Select "Hibernate" from the drop-down lists under "On Battery" and "Plugged In." Click "Save Changes." Your laptop will now bypass Standby mode when you close the lid and it will enter Hibernate mode instead. Hope it helps.

Jan 23, 2013 | Gateway MT6730 Notebook PC

1 Answer

When i try to turn on my sony kv-27fs12 keep turn off and blink 4 time a red led make a pause and keep blinking 4 times, what that could be?


Four blinks - No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal muted. Check IC1509, Q1505
Vertical sweep failure. Check all the solder terminals to vertical output IC. If it do not help, replace that IC.

Jul 03, 2012 | Sony KV-27FS12 27" TV

1 Answer

Turns off after 2 or 3 seconds then red light flashes 4 times


Four blinks - No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal muted. Check IC1509, Q1505

Keep us updated.

Dec 22, 2010 | Sony KDF-E50A10 50 in. LCD HDTV

1 Answer

Turn signals front and back have stopped working. I think it may be a circuit breaker, but im not sure which one. 1984 iron head sporty


The circuit breaker with the blue wires coming off of it is the one for the lights. If you need a schematic, contact me directly wd4ity@bellsouth.net. Check for voltage at the blue wires on the circuit breaker. Then check all four bulbs. If one bulb is blown, the other one on that side will light up but not blink.

Good Luck
Steve

Jul 27, 2010 | Harley Davidson XLH 1000 Sportster...

1 Answer

Tv shuts off then standby light flashes 4 times


hello Four blinks - No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal muted. Check IC1509, Q1505

regards
shaun

Jan 20, 2010 | Sony Televison & Video

1 Answer

Standby light blinks and tv won't turn on


Four blinks = No vertical Deflection (V STOP), Screen goes to a single horizontal line then the video signal muted. Check IC1509, Q1505

Dec 27, 2008 | Televison & Video

1 Answer

Red light on front blinks 4 times


A four blink code indicate loss of the vertical deflection pulse. In layman's terms the vertical Ic or something like a cap or diode in that circuit have failed or is failing causing a loss of the pulse signal and the shutdown circuit is keeping the set from causing any severe damage... The self diagnostic is a great tool for these minor problem and saves the customer hundreds from overdriving the problem and making it worse.
The set needs to be taken to a reputable shop and repaired. Not something you can just do yourself short of having a scope and knowing hwat to do with it, the vertical circuit will have to be trace and signal tested to isolate the exact failure.
Bill

Dec 07, 2007 | Sony KP-57HW40 57" Rear Projection...

Not finding what you are looking for?
2008 Harley Davidson FXD Dyna Super Glide Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...