Question about 2009 Harley Davidson FXCWC Rocker C

1 Answer

R there freeway crash bars for a 2008 rocker c

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,301 Answers
Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for 2008 up lander 3.9 engine


Upper intake manifold says 18 ft lbs
rocker arm cover says 89 in lbs

Dec 03, 2016 | 2008 Chevrolet Uplander

1 Answer

How to replace ignition switch on a hyundai tiburon


Removal & Installation

Specific to:
Hyundai Entourage 2007-2008
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative (-) battery terminal.
  3. Remove the crash pad lower panel (A).

    0996b43f80e41e86.jpg
    enlarge_icon.gifenlarge_tooltip.gif
    Fig. Remove the crash pad lower panel (A)
  4. Remove the 2 screws (A) and the trip switch connector.
  5. Remove the crash fascia panel (B).

    0996b43f80e41e87.jpg
    enlarge_icon.gifenlarge_tooltip.gif
    Fig. Remove the crash fascia panel (B)
  6. Remove the screw with the ignition in the ON position (IG ON) and disconnect the 6P connector.
  7. Remove the ignition switch (A).
  8. Installation is the reverse of removal procedure.

    0996b43f80e41e88.jpg
    enlarge_icon.gifenlarge_tooltip.gif
    Fig. Remove the ignition switch (A)
Specific to:
Hyundai Accent 2006-2008
Hyundai Azera 2006-2008
Hyundai Elantra 2006-2008
Hyundai Sonata 2006-2008
Hyundai Tiburon 2006-2008
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    The negative battery terminalThe crash pad lower panelThe ignition switch after loosening the screw with IG ON and disconnecting the 6P connector
  3. Installation is the reverse of the removal procedure.hope this helps it is off autozone website

Aug 02, 2014 | 2006 Hyundai Tiburon

1 Answer

Why does my stabilitrak service light come on when I'm on the freeway?


Have a repair shop check for codes--- SOON---
& diagnose that system

There is no guessing at vehicle problems

Running fine is ---in your mind---

Your asking about a braking system issue,
not engine performance issue

Read your owners manual

Read anyone's owners manual

Obviously the vehicle has a problem,that has to be found,
& a solution found & you pay for all that & the repair

Jul 25, 2014 | 2008 Pontiac Torrent

1 Answer

Rocker arm specs


ROCKER ARM SUPPORT PLATE
Installing the rocker arms and rotating the engine with the valve
train loaded can result in bent push rods, damaged bushings
or a warped support plate.

To install the rocker arm support plate, both lifters of the
cylinder being serviced must be on the base circle (or
lowest position) of the cam.
Place the rocker arm support plate assembly into the rocker housing. Loosely install the four
rocker arm support plate bolts with flat washers.
Tighten the rocker arm support plate bolts in a cross pattern and alternately tighten
each of the four rocker arm support plate bolts just 1/4 turn. THEN continue turning the bolts in these increments until snug. THEN following the same sequence, tighten the bolts to 18-
22 ft-lbs (24.4-29.8 Nm).

THEN install and alternately tighten the two bolts to secure breather assembly to 90-120 in-lbs (10.2-13.6 Nm).

May 12, 2014 | 2008 Harley Davidson FXD Dyna Super Glide

1 Answer

How do i install freeway foot pegs


Most people install a front engine guard (crash bar) and put the freeway foot pegs on that.

Mar 29, 2010 | 2005 Harley Davidson FLHRS - FLHRSI Road...

1 Answer

Would like to install crash bars on a virago xv250. How do I do this? Thanks.


Installing the crash bars depends on the brand you purchased. They usually come with instructions.
In any case, crash bars are attached to the upper section of the frame, on each side of the foot-pegs and under the main bolts of the engine block.
The crash-bars should stay rigid, without any vibration nor limit access to the foot/hand contols.

Dec 01, 2009 | 1996 Yamaha Xv 250 Virago S

Not finding what you are looking for?
2009 Harley Davidson FXCWC Rocker C Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4340 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...