Question about Aprilia FLHRSI Road King Custom Motorcycles

1 Answer

Bigend knocking how difficult to replace - FLHRSI Road King Custom Aprilia Motorcycles

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

If it a 2 stroke rs,,not easy,as fly wheel puller is a funny size,,,and when you get crank casings apart,,,gear coggs come apart,,,,BEWARE,,,

Posted on May 28, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I get a knocking sound from the engine of my 2007 Mondeo 1.8 tdci. Doesn't happen all the time but when it does seems to clear when I rev engine.

Seems the engine is smoking. Maybe your bigend bearings are worn out, . May have to replace piston rings along with main n con bearings

Jan 19, 2018 | Cars & Trucks

1 Answer

2005 Sebring Touring 2.7. Where is the knock sensor located?

This knock sensor is very difficult to access. It is located between the two cylinder banks, it screws into the cylinder block underneath the intake manifold.

In order to remove the sensor the intake manifold and right cylinder head must be removed.


Aug 23, 2015 | Chrysler Sebring Cars & Trucks

3 Answers

Chana star 1000cc:Torque settings,main bearing,bigend bearing &cylinder head.


Aug 06, 2013 | Cars & Trucks

1 Answer

2.8 liter engine metallic noise when running

IF you have a timing chain it will come as a rattle if worn. If worn hydraulic tappets they will tap excessively at idle on lower oil pressure. If it is a knock the by removing each plug lead in turn and it alters it may be a bigend or main bearing A tinny rattle may be a failing drive plate (flexiplate) that teh torque converter is bolted to

Feb 23, 2013 | GMC Cars & Trucks

1 Answer

I have an engine code PO332 knock sensor 2 circuit low imput bank 2 what is this problem .the car is a 2001 gmc yukon xl .

The most likely cause of your code is a bad rear knock sensor. You should check the knock sensor wiring harness for corrosion. But if that checks out the sensor will have to be replaced. The knock sensor is under the intake manifold, although it's not too difficult to remove. Both knock sensors should be replaced along with the wiring harness, just because of labor involved in gaining access to the sensors. You could try clearing the code, it may stay off for a long time.

May 23, 2010 | 2001 GMC Yukon XL

1 Answer

XJ8 Knock Sensor

Pretty Difficult you have to remove the complete intake and injector rail. You will need both side intake gaskets and the plenum gasket.

Dec 12, 2008 | 2001 Jaguar XJ8

2 Answers

Loud mechanical knock in engine 2.8 a4 Audi 1996

it's probably a rod knocking and that's never too good. get it checked out with a mechanic soon. Some auto parts sell stuff to stop that so you can go there and ask they usually help you, but it won't solve the problem it will just stop the noise for a little bit.

Oct 30, 2008 | 1996 Audi A4

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Aprilia Experts


Level 3 Expert

79865 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4903 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you an Aprilia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides