Question about Suzuki GS 750 Motorcycles

Open Question

I am looking for the torque setting for the cylinder head bolts of a 1982 suzuki gs1100g I am also looking for the torque for the nut that holds on the flange on the drive output shaft from the gearbox as this is a shaft drive bike

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 254 Answers

SOURCE: Need torque wrench settings for cylinder head bolts

try here http://www.manualz.info/

hope this helps

Posted on Jan 04, 2009

Ad
bunnydawg
  • 5158 Answers

SOURCE: 91 kx 250 torque values

Engine Top End:
Auto Decompressor Bolt 104 in·lb
Cylinder Head Cover Bolts 87 in·lb
Cylinder Head Bolts: M10 36 S
M6 104 in·lb S

the S in that means the specified pattern ... just like tightening car tire bolts... please note all that it its INCH lbs....

don't know why it says just 36 for the M10 bolts unless they left out inch lbs

Anything else let me know as i've got a manual for the 250 f... actually i've got a few different ones

Robert

Please take a moment to rate this solution as i've taken a few minutes to find the manual thanks

Posted on Jan 28, 2009

Moto-Wiz
  • 34 Answers

SOURCE: what is the head bolt torque on a 1990 suzuki lt250r

The 8mm head bolts are torqued at 19 - 21 ft/lbs.
any smaller 6mm bolts are torqued to only 6 ft/lbs
like those on the lower cylinder.

Posted on Aug 22, 2009

  • 86 Answers

SOURCE: i need head bolt torque specs for a suzuki 80cc

cylinder is 25-29newton meters head is the same.

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need the head bolt torque specs and sequence for a 2008 Suzuki reno 4 cylinder


well it's at alldata.com and at suzuki pitstop plus dot com.
here ill do that for you....
4 banger no displacement stated, now that is a challenge.


now the words..... USA car... 2.0L vin Z

Cylinder head bolts. Tighten the cylinder head bolts gradually and in the sequence shown. Tighten the cylinder head bolts to 18 ft. lbs. (25 Nm) and turn the bolts another 3 turns of 90 degrees using the angular torque gauge KM-470-B.




25750556-4duymjxl1ar05igx5z0a5r0z-5-0.jpg

Jun 17, 2015 | 2008 Suzuki Reno

1 Answer

How do I remove ignition key cylinder from 1982 Suzuki gs1100g motorcycle?


REMOVE THE TOP YOLK AND LOOK UNDER THE BOTTOM THERE ARE 2 SNAP SCREWS OR SECURITY BOLTS, IF SNAP SCREWS A VERY THIN CHISSELL AND TAP IT ROUND TO LOSEN IT, IF SECURITY screw u need a tool for it

Mar 15, 2015 | Suzuki Motorcycles

1 Answer

What is the cylinder head bolt torque pattern on a 2007 suzuki forenza


post engine size. they use like 6 engines.
open hood, look up , see that EPA tag, it says right there.
no man on earth can guess engines. not ever.
(sure, rare exeptions, on 2 door sports cars)

Aug 20, 2014 | 2007 Suzuki Forenza

1 Answer

Could you advise what are the cylinder head bolt tension settings for hyundai lantra j5. Could you email me back on judy.ben@optusnet.com.au. Thanks


let me see if i can get some info 4 you.

edit
REMOVAL

1. Drain the coolant and disconnect the upper radiator hose.
2. Remove the breather hose (between the air cleaner and the head cover).
3. Remove the air-intake hose.
4. Remove the vacuum hose, fuel hose and coolant hose.
5. Remove the cables from the spark plugs. The cables should be removed by holding the boot portion.
6. Remove the ignition coil.
7. Remove the power steering oil pump and bracket.
8. Remove the intake manifold.
9. Remove the heat protector and exhaust manifold assembly.
10. Remove the coolant pump pulley and the crankshaft pulley.
11. Remove the timing belt cover.
12. Remove the timing belt tensioner pulley.
13. Remove the timing belt.
14. Remove the head cover.


15. Remove the cylinder head assembly. The cylinder head bolts should be removed by using Special Tool, Cylinder Head Bolt Wrench (09221-32001) or equivalent, in the sequence as shown in the illustration in two or three steps.
16. Remove the gasket pieces from the cylinder block top surface and cylinder head bottom surface. NOTE: Make sure that the gasket pieces do not fall in the engine.

INSTALLATION

1. Clean all gasket surfaces of the cylinder block and the cylinder head.
2. Install a new cylinder head gasket onto the cylinder head assembly. Apply sealant to the gasket and do not reuse the old cylinder head gasket.


3. Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
4. Install the timing belt tensioner pulley.
5. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
6. Adjust the timing according to "Timing Belt"
7. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

8. Install the timing belt cover.
9. Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
10. Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
11. Install the surge tank and tighten the nuts bolts to the specified torque.
12. Install the power steering oil pump and bracket.
13. Install the ignition coil.
14. Install the air intake hose.
15. Connect the vacuum hose, fuel hose and water hose.
16. Install breather hose.

Jun 08, 2011 | Hyundai Elantra Cars & Trucks

1 Answer

Whats is te cylinder heads torque for suzuki aerio 2.3 lts


Hi! Please don't forget to rate! Thanks!



c17hydro_181.gif

Cylinder head bolt torque sequence-2.0L and 2.3L engines



Apply engine oil to the bolt threads and tighten the cylinder head bolts, in sequence, using the following 6 Steps:

  • Step 1: 38.5 ft. lbs. (53 Nm)
  • Step 2: 61 ft. lbs. (84 Nm)
  • Step 3: Loosen all of the cylinder head bolts
  • Step 4: 38.5 ft. lbs. (53 Nm)
  • Step 5: 76 ft. lbs. (105 Nm)
  • Step 6: Bolt M6 (bottom left of cylinder head) - 8 ft. lbs. (11 Nm)

May 12, 2011 | 2003 Suzuki Aerio

1 Answer

I have a 1982 Suzuki RM-125. I am having difficulty removing the cylinder head and cylinder, all bolts have been removed. It's just really stuck


Here's the easiest way:

Put the head bolts back on snug. Put the spark plug back in snug. Put the cylinder base nuts back on but leave them about 1/4" away from seat. Now give the kickstarter a swift hit down - you can do this by hand. Repeat until the cylinder pops up. Now, loosen the head nuts and repeat.

This is the easiest way to remove a cylinder.

Hope this helps.

Apr 29, 2011 | 2003 Suzuki RM 125

3 Answers

What are the specs for tourquing down a cylinder head on a 2001 suzuki ls 650. thanx, p.j.


From what I have found from here.

http://www.repairmanualclub.com/motomanuals/

http://forum.svrider.com/gallery/showphoto.php?photo=706&ppuser=21996

Mar 05, 2011 | 2003 Suzuki LS 650 Savage

1 Answer

Have a 1982 suzuki motorcycle gs1100gk starter turns magneto but is not cranking engine is this a keyway problem


Actually no this happened because the bolt holding the magneto on was not properly tighten to the correct torque a loose rotor will shear the key remove the rotor and inspect the key way remove what left and install a new set key and properly torque the bolt.

Apr 05, 2010 | 1983 Suzuki GSX 1100 E

1 Answer

Head bolt torque settings


8mm nut= 16.5 to19.5 lb/ft
9mm nut =21 to 24 lb/ft..

Sep 24, 2009 | 1988 Suzuki LS 650 Savage

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...