Question about 2003 Victory Vegas

1 Answer

Check engine light came on after I had it serviced. All that was done was installed a new battery and corrected the relay connection from the battery --> relay --> starter. She has run great since I purchased her and still does only now the check engine light which was never on before remains lit and the battery / relay work was the only thing done to the bike at the service shop. The closet Victory dealer is 4 hours away so any help would be greatly appreciated.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Victory Master
  • 43,050 Answers

Hi, Swatic00 there may be a generated fault code that needs to be reset for this scenario you will need your service/owners manual if you can't find the best tool you ever bought for your Victory, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Check Engine Light Came On
Victory motorcycle tip for the check engine light motorcycles
Error codes
02 04 VICTORY Service Manual 02 04 pdf
03 Vegas parts manual pdf
Victory Motorcycles 2005 Vegas Owner Manual

Posted on Jun 09, 2017

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 653 Answers

SOURCE: My 2003 V92C Victory Idles too low. The only

Seek and you shall be answered. Google it

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2010 Patriot won't starter key works lights horn new starter & battery checked 30 amp fuses starter


WHAT ????? want to try again .

2010 Patriot won't start ,key work's , light's ,horn ,new starter and battery ! checked 30 amp fuse's starter ?????? Maybe you should take it to a qualified repair shop .Sounds like you have no clue.

Feb 01, 2017 | Cars & Trucks

2 Answers

Service engine soon light, and code P0410 Secondary air injection system malfunction.. what are the items to look for? what normally fixes the fault? Thanks


Water may have collected in the AIR pump or the vent solenoid and frozen or corroded the pump.

Correction
Replace the AIR pump and install a new inlet hose and solenoid tube assembly using the following procedure:
1. Prep vehicle.
2. Raise vehicle on hoist.
3. Remove shield covering AIR pump.
4. Remove hose and vacuum lines from pump and solenoid.
5. Remove AIR pump inlet hose. Do not re-use.
6. Disconnect electrical connectors from pump and solenoid.
7. Remove pump mounting bolts and pump.
8. Transfer isolators from the old pump to the new pump.
9. Install new AIR pump and bolts to vehicle. Tighten the bolts to 17 N.m (12.5 lb ft)
10. Route new hose assembly up between engine and fender. It should come up near the area between the battery and the coolant bottle.
11. Connect new inlet hose to pump inlet.
12. Connect old outlet hose to pump outlet.
13. Connect electrical connector to pump.
14. Connect electrical connector for solenoid to connector on the new hose assembly.
15. Connect the hose with the white nipple to the vacuum source hose.
16. Connect the remaining hose to the shut off valve.
17. Install shield covering AIR pump.
18. Lower vehicle.
19. Remove coolant reservoir nut nearest the battery.
20. Route new hose assembly between the battery and the coolant reservoir with the solenoid on top.
21. Install the solenoid bracket onto the coolant reservoir stud and reinstall the nut back into the vehicle.
22. Use a wire tie to keep the new hose assembly away from the engine. On four cylinder engines, tie to the AIR outlet hose. On six cylinder engines, tie to an available hole in the radiator fan shroud.

Hope that helps......... //

Aug 01, 2008 | GMC Jimmy Cars & Trucks

1 Answer

2005 Limited. Why doesn't it start?


have battery checked, if it has an internal short boosting it won`t start it. also check battery cable connections at both ends for corrosion.

Aug 23, 2015 | Chrysler PT Cruiser Cars & Trucks

1 Answer

Ignition issue


Have a load test done on the battery to check for a failing cell. Check battery terminals are shiny clean and tight. Check for power from the ignition switch to the starter solenoid as this is the circuit you by pass when you short out the starter terminals.

Sep 21, 2013 | 2000 Ford F350 Super Duty Super Cab

1 Answer

How to change oil pan gasket for 2005 dodge caravan


Caravan, Grand Voyager, Town and Country, Voyager, 2000-2004

Oil Pan - Removal & Installation

2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Structural collar A/C compressor bracket to oil pan bolt Oil pan
  4. Clean the oil pan and all gasket mating surfaces.
To install:
  1. Install or connect the following:
    Oil pan gasket to the block after applying engine RTV at the oil pump parting line Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Structural collar Negative battery cable
  2. Fill the crankcase to the correct level.
  3. Start the engine, check for leaks and repair if necessary.

3.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Starter motor Front motor mount bracket Bending braces Torque converter dust shield Oil pan

    e6c7cfd.jpg
    Fig. Oil pan mounting bolt tightening sequence-3.0L engine

To install:
  1. Clean the oil pan all mating surfaces.
  2. Apply RTV gasket material to the oil pan.
  3. Install or connect the following:
    Oil pan. Tighten the bolts in sequence to 50 inch lbs. (6 Nm). Torque converter dust shield Bending braces Front motor mount bracket Starter motor Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

3.3L & 3.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Engine oil dipstick Drive belt splash shield Strut to transaxle attaching bolt and loosen the strut to engine attaching bolts Transaxle case cover Oil pan fasteners Oil pan and gasket

To install:
  1. Clean the oil pan and all mating surfaces.
  2. Apply a 1 / 8 inch bead of gasket material at the parting line of the chain case cover and the real seal retainer.
  3. Install or connect the following:
    New gasket on the oil pan Oil pan. Torque the bolts to 105 inch lbs. (12 Nm). Transaxle case cover All bending brace bolts Drive belt splash shield Engine oil dipstick Negative battery cable
  4. Fill the crankcase to the correct level.
  5. Start the engine, check for leaks and repair if necessary.

Hope helps (remember rated this).

Jun 24, 2010 | 2005 Dodge Caravan

2 Answers

Electric Radiator Fan Does Not Come On


Chevy dealer says will not come on until temperature reaches 219 f

May 16, 2010 | 2007 Chevrolet Silverado 1500 2WD

3 Answers

Pulseating dome lights head lights and park lights


It definately sounds as though your alternator is failing. Also you may want to pull and clean your battery terminals. Thanks, Dana

Sep 22, 2009 | 2003 Dodge Caravan

2 Answers

Battery light on 1999 Ford Explorer


first, check battery voltage with engine off. It should be @ 12 1/2 volts.
With engine running, it should be @ 14 volts.
If yes, then check for a bad connection at alternator. Look closely at the terminals for corrosion.
There should be BK/DG wire supplying charging amperage to the battery. It does not go through a relay.
Check the mega fuse (175 amp) in the battery junction box (ride side or engine compartment I think). check connection 122 & 197 in same area. good luck

3ca1c98.gif

Apr 10, 2009 | 1999 Ford Explorer

1 Answer

1991 olds cutlass supreame 3.1


Did you check the starter relay and make sure that all the connections to the starter are correct?

Apr 04, 2009 | 1991 Oldsmobile Cutlass Supreme

Not finding what you are looking for?
2003 Victory Vegas Logo

Related Topics:

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Victory Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Joseph Hoffmann

Level 3 Expert

1702 Answers

Are you a Victory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...