Question about 2003 Suzuki GSX 600 F (Katana)

1 Answer

What are the to lines under the start button - 2003 Suzuki GSX 600 F (Katana)

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 84 Answers

The two cables under the start button are your throttle cables (push /pull)

Posted on May 25, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Red line side to side under start button pls help

Your screen is dying. Your screen will develop another line(s) sooner or later. If it is not acceptable anymore, then you can replace your screen. You can look for it on eBay.

Feb 18, 2014 | Toshiba Satellite Computers & Internet

1 Answer

How do I reset the service alarm on all Intellisys controllers of Ingersoll Rand?

when controller says ready to start you must press display select button then hidden left button which you can feel as a raised
arrea under the membrane between the display select button and the orange ringed centre button. the screen should say checking machine a nd then ready to start if it has reset. if it comes up with line pressure then you must get back to ready to start and repeat method. this assumes the compressor has the SE Controller with green LCD screen

Oct 02, 2013 | Ingersoll Rand Air Tools & Compressors

1 Answer

Won't start dial shows h:01

You have set the delay start. Press the button that says "finish in" or "delay start" (depending on the model) unit it is zero. Either that or you have entered the hardness setting and this should come off by just turning to the off position. Some of these d/ws aalso have a reset which is acheived by pressing two buttons simultaneously and this should be printed on the panel (dot under each button joined by a line) or hold the start button. (You haven't supplied the ENr so I have tried to give all possible scenarios) Post ENr if none of the above works.

Mar 19, 2013 | Bosch Dishwashers

1 Answer


Sounds like your transfer and pick up button are actually direct inward dial (DID) lines. To see whats programmed under those buttons, press feature *0 then press your transfer button. It will probably give you a line number and port assignment for the line.

Sep 20, 2010 | NorStar T7208 Corded Phone

1 Answer

The option and cylce button on the control panel

bleed out the water line to the dish washer (under the dishwasher) be cause a lack of water or an air pocket to a sincor will make it not start or delay to start.

Aug 17, 2009 | Dishwashers

3 Answers

My cummins turbo diesel ran out fuel, now it wont start

You need to loosen three (1,3, and 5 are the easiest to get to) of the injector lines at the cylinder head with a 19 mm wrench. Have someone crank the motor until you see fuel come out. Immediately start to tighten the lines, while the motor is still cranking. The motor will start to catch as the lines get tightened. Let it run a few minutes to eliminate the rest of the air.
I've had to do this several times on my 99 Ram because of a messed up sending unit telling me I still had a half tank.
The mechanics at Mt. Clemens Dodge taught me this. Good Luck.

May 24, 2009 | 1999 Dodge Ram

1 Answer

The program light goes off and the BF162 doesn't start...

When you keep the button pressed for a few seconds the lights go off, this resets the dishwasher. Then press the p button again to the program you want 1st light is heavy soil 2nd light is normal soil, 3rd light is eco wash, 4th light is rinse. At the end of the cycle the program light you have selected will flash.

Apr 24, 2009 | Hotpoint 23 in. BFI62 Built-in Dishwasher

1 Answer

Kenmore 13114 Start Button Fell Off After 3 months

Sears will definitely come fix that under the warranty. I was in that line of work for years, and we would come fix any problem on a machine under warranty.

Mar 14, 2009 | Dishwashers

1 Answer

Broken Button

The trip spring under the return keytop needs replacement. Lawrence

Jul 24, 2008 | Lexmark Wheelwriter 1000 Typewriter

3 Answers

My eagle talon will not start

Search for a way to reset the alarm. Also take the fuel lines off the engine and test the fuel pressure. You want to eliminate the fuel pump not working. If it has a reset button for the fuel pump try that. I would start at the fuel pump and worlk my way up.

Jun 24, 2008 | 1993 Eagle Talon

Not finding what you are looking for?
2003 Suzuki GSX 600 F (Katana) Logo

Related Topics:

44 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

80608 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4988 Answers


Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides