Question about 2003 Harley Davidson FLHT Electra Glide Standard

1 Answer

I hit the start button and it just clicks. battery is 12.5 volts. No relay. Need to test or replace starter? Do i need to remove primary and oil tank?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,100 Answers

Before you tear into it, can you get it jumped to see if it is the starter or the battery? The battery , even at 12.5v, should crank it over, a clicking sound is not that of a bad starter but a week battery. I would suspect the battery, if you can get it out, check the water level and the check the electrolyte condition in each cell. I am not familiar with the removal of your starter, but would check the battery first. Hope this helps.

Posted on May 25, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 Kawasaki VN 1600 Mean Streak will not turn over just clicks


Hi, Anonymous you turn on the ignition switch press the starter button and all you get is the dreaded "CLICK" or "CLUNK" now before testing any electrical component in the Starter System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries. Depending on battery voltage starter relays and starter solenoids can make the same noise when you hit the starter button. You can easily determine which one is at fault by the following two simple tests:
STARTER RELAY- place your thumb and index finger on the starter relay and press the starter button, if you feel the click then the relay is faulty and needs to be replaced.
STARTER SOLENOID- bridge the positive and negative poles of the solenoid with a small screwdriver if you get a loud clunk then the solenoid needs to be rebuilt or replaced as necessary. If the engine turns over then replace the starter relay otherwise the usual suspects for a faulty starter solenoid are:
1. Battery terminals have loose or corroded connections.
2. Battery cables faulty due corroded or broken internal wiring at the cable connector especially the "NEGATIVE" cable which needs to be checked at "BOTH" ends.
3. Battery voltage, must be 12.5 volts or better, voltage from the battery to the main circuit breaker to the ignition switch to the security/ignition fuse to the TSM/TSSM module to the engine stop/run switch to the starter button to the starter relay to the green wire that connects to the starter solenoid must not drop more than 1/2 volt of battery voltage.
4. Disconnect spark plug cables, with a voltmeter connected to the battery, the ignition switch in the on position, the kill switch in the run position, the starter button depressed, starter engagement should not bring voltage below 9.6 volts DC. If the voltage is below 9.6 the battery is faulty and must be replaced. I "HIGHLY" recommend a maintenance free AGM battery typically they have more amperage for cranking.
5. Faulty starter relay, check continuity.
6. Faulty starter solenoid, check contact plate and shoes for excessive electrical erosion/etching, refurbish as necessary or invert contact plate and use the virgin backside. Check contact shoes for being loose. Replace solenoid if the negative function is still a final outcome.
7. Faulty starter, bench test starter with a 12-volt battery if negative function check, decontaminate and undercut armature commutator segments as necessary, check segments with an ohmmeter probe each one and the segment next to it for shorts. Have the armature tested with a growler and field coils, and brush plate with an ohm-meter for opens, shorts or grounds. Replace brushes if less than .438" It is generally cheaper to overhaul/refurbish a starter motor than buying a new one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike Won START clicks won turn over
My Bike won start
KAWASAKI VN1600 MEAN STREAK Service Manual
OEM Parts for Kawasaki
2004 Kawasaki Vulcan 1600 Mean Streak Owner Manual

Jul 07, 2014 | 2004 kawasaki VN 1600 Mean Streak

1 Answer

1998 Kawasaki EN 500 Vulcan Classic solenoid chatters when trying to start


Hi, Anonymous you turn on the ignition switch press the starter button and all you get is the dreaded "CLICK" or "CLUNK" now before testing any electrical component in the Starter System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries. Depending on battery voltage starter relays and starter solenoids can make the same noise when you hit the starter button. You can easily determine which one is at fault by the following two simple tests:
STARTER RELAY- place your thumb and index finger on the starter relay and press the starter button, if you feel the click then the relay is faulty and needs to be replaced.
STARTER SOLENOID- bridge the positive and negative poles of the solenoid with a small screwdriver if you get a loud clunk then the solenoid needs to be rebuilt or replaced as necessary. If the engine turns over then replace the starter relay otherwise the usual suspects for a faulty starter solenoid are:
1. Battery terminals have loose or corroded connections.
2. Battery cables faulty due corroded or broken internal wiring at the cable connector especially the "NEGATIVE" cable which needs to be checked at "BOTH" ends.
3. Battery voltage, must be 12.5 volts or better, voltage from the battery to the main circuit breaker to the ignition switch to the security/ignition fuse to the TSM/TSSM module to the engine stop/run switch to the starter button to the starter relay to the green wire that connects to the starter solenoid must not drop more than 1/2 volt of battery voltage.
4. Disconnect spark plug cables, with a voltmeter connected to the battery, the ignition switch in the on position, the kill switch in the run position, the starter button depressed, starter engagement should not bring voltage below 9.6 volts DC. If the voltage is below 9.6 the battery is faulty and must be replaced. I "HIGHLY" recommend a maintenance free AGM battery typically they have more amperage for cranking.
5. Faulty starter relay, check continuity.
6. Faulty starter solenoid, check contact plate and shoes for excessive electrical erosion/etching, refurbish as necessary or invert contact plate and use the virgin backside. Check contact shoes for being loose. Replace solenoid if the negative function is still a final outcome.
7. Faulty starter, bench test starter with a 12-volt battery if negative function check, decontaminate and undercut armature commutator segments as necessary, check segments with an ohmmeter probe each one and the segment next to it for shorts. Have the armature tested with a growler and field coils, and brush plate with an ohm-meter for opens, shorts or grounds. Replace brushes if less than .438" It is generally cheaper to overhaul/refurbish a starter motor than buying a new one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike won start grinding clicking sound
Starter clicking not turning over Kawasaki Vulcan 750 Forum Kawasaki VN750...
Kawasaki EN500 Service Manual
OEM Parts for Kawasaki
1998 Kawasaki Vulcan 800 Classic Owner Manual

Jun 12, 2014 | 1998 kawasaki EN 500 Vulcan Classic

2 Answers

1984 XLS Roadster Iron Head. Why doesn't it start?


HI YOU MITE TRY PUTING A METER OR A TEST LIGHT ON THE STARTER SOLENOID TREMINAL SMALL WIRE AND HIT THE START BUTTON TO SEE IF THE LIGHT COME ON ,IF NOT THE WIRE IS OPEN .IF LIGHT COME ON THEN THE STERTER NEED REPAIR OR REPLACE.

Feb 05, 2014 | 2004 Harley Davidson XL 1200 R Sporster...

1 Answer

1998 Kawasaki VN 1500 Vulcan Classic starter just clicks


Hi, Tim you turn on the ignition switch press the starter button and all you get is the dreaded "CLICK" or "CLUNK" now before testing any electrical component in the Starter System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries. Depending on battery voltage starter relays and starter solenoids can make the same noise when you hit the starter button. You can easily determine which one is at fault by the following two simple tests:
STARTER RELAY- place your thumb and index finger on the starter relay and press the starter button, if you feel the click then the relay is faulty and needs to be replaced.
STARTER SOLENOID- bridge the positive and negative poles of the solenoid with a small screwdriver if you get a loud clunk then the solenoid needs to be rebuilt or replaced as necessary. If the engine turns over then replace the starter relay otherwise the usual suspects for a faulty starter solenoid are:
1. Battery terminals have loose or corroded connections.
2. Battery cables faulty due corroded or broken internal wiring at the cable connector especially the "NEGATIVE" cable which needs to be checked at "BOTH" ends.
3. Battery voltage, must be 12.5 volts or better, voltage from the battery to the main circuit breaker to the ignition switch to the security/ignition fuse to the TSM/TSSM module to the engine stop/run switch to the starter button to the starter relay to the green wire that connects to the starter solenoid must not drop more than 1/2 volt of battery voltage.
4. Disconnect spark plug cables, with a voltmeter connected to the battery, the ignition switch in the on position, the kill switch in the run position, the starter button depressed, starter engagement should not bring voltage below 9.6 volts DC. If the voltage is below 9.6 the battery is faulty and must be replaced. I "HIGHLY" recommend a maintenance free AGM battery typically they have more amperage for cranking.
5. Faulty starter relay, check continuity.
6. Faulty starter solenoid, check contact plate and shoes for excessive electrical erosion/etching, refurbish as necessary or invert contact plate and use the virgin backside. Check contact shoes for being loose. Replace solenoid if the negative function is still a final outcome.
7. Faulty starter, bench test starter with a 12-volt battery if negative function check, decontaminate and undercut armature commutator segments as necessary, check segments with an ohmmeter probe each one and the segment next to it for shorts. Have the armature tested with a growler and field coils, and brush plate with an ohm-meter for opens, shorts or grounds. Replace brushes if less than .438" It is generally cheaper to overhaul/refurbish a starter motor than buying a new one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike Won START clicks won turn over
http://tearitupfixitrepeat.blogspot.com/2010/08/if-your-1500-vulcan-wont-start.html
http://www.vulcansabs.com/wp-content/uploads/2016/04/Kawasaki-Vulcan-VN1500-Nomad-Classic-Tourer-1998-1999-Service-Manual.pdf
OEM Parts for Kawasaki
1998 Kawasaki Vulcan 1500 Classic Owner Manual

Feb 04, 2014 | 1998 kawasaki VN 1500 Vulcan Classic

1 Answer

1998 Kawasaki VN 1500 Vulcan Classic starter solenoid clicks


Hi, Anonymous you turn on the ignition switch press the starter button and all you get is the dreaded "CLICK" or "CLUNK" now before testing any electrical component in the Starter System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries. Depending on battery voltage starter relays and starter solenoids can make the same noise when you hit the starter button. You can easily determine which one is at fault by the following two simple tests:
STARTER RELAY- place your thumb and index finger on the starter relay and press the starter button, if you feel the click then the relay is faulty and needs to be replaced.
STARTER SOLENOID- bridge the positive and negative poles of the solenoid with a small screwdriver if you get a loud clunk then the solenoid needs to be rebuilt or replaced as necessary. If the engine turns over then replace the starter relay otherwise the usual suspects for a faulty starter solenoid are:
1. Battery terminals have loose or corroded connections.
2. Battery cables faulty due corroded or broken internal wiring at the cable connector especially the "NEGATIVE" cable which needs to be checked at "BOTH" ends.
3. Battery voltage, must be 12.5 volts or better, voltage from the battery to the main circuit breaker to the ignition switch to the security/ignition fuse to the TSM/TSSM module to the engine stop/run switch to the starter button to the starter relay to the green wire that connects to the starter solenoid must not drop more than 1/2 volt of battery voltage.
4. Disconnect spark plug cables, with a voltmeter connected to the battery, the ignition switch in the on position, the kill switch in the run position, the starter button depressed, starter engagement should not bring voltage below 9.6 volts DC. If the voltage is below 9.6 the battery is faulty and must be replaced. I "HIGHLY" recommend a maintenance free AGM battery typically they have more amperage for cranking.
5. Faulty starter relay, check continuity.
6. Faulty starter solenoid, check contact plate and shoes for excessive electrical erosion/etching, refurbish as necessary or invert contact plate and use the virgin backside. Check contact shoes for being loose. Replace solenoid if the negative function is still a final outcome.
7. Faulty starter, bench test starter with a 12-volt battery if negative function check, decontaminate and undercut armature commutator segments as necessary, check segments with an ohmmeter probe each one and the segment next to it for shorts. Have the armature tested with a growler and field coils, and brush plate with an ohm-meter for opens, shorts or grounds. Replace brushes if less than .438" It is generally cheaper to overhaul/refurbish a starter motor than buying a new one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Bike Won START clicks won turn over
My Kawasaki Vulcan 1500 makes very quiet clik sound but
http://www.vulcansabs.com/wp-content/uploads/2016/04/Kawasaki-Vulcan-VN1500-Nomad-Classic-Tourer-1998-1999-Service-Manual.pdf
OEM Parts for Kawasaki
1998 Kawasaki Vulcan 1500 Classic Owner Manual

Jul 24, 2013 | 1998 kawasaki VN 1500 Vulcan Classic

1 Answer

Yahmaha roadstar starter problems


is there 12 volts going to the starter motor when the button is pressed to start it?? if not you need a battery. battery should be 12.6 volts at rest.

Feb 23, 2018 | Motorcycles

1 Answer

Honda Dylan 125 handlebar clicking noise


Hi, Stevesmit399 you turn on the ignition switch press the starter button and all you get is the dreaded "CLICK" or "CLUNK" now before testing any electrical component in the Starter System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries. Depending on battery voltage starter relays and starter solenoids can make the same noise when you hit the starter button. You can easily determine which one is at fault by the following two simple tests:
STARTER RELAY- place your thumb and index finger on the starter relay and press the starter button, if you feel the click then the relay is faulty and needs to be replaced.
STARTER SOLENOID- bridge the positive and negative poles of the solenoid with a small screwdriver if you get a loud clunk then the solenoid needs to be rebuilt or replaced as necessary. If the engine turns over then replace the starter relay otherwise the usual suspects for a faulty starter solenoid are:
1. Battery terminals have loose or corroded connections.
2. Battery cables faulty due corroded or broken internal wiring at the cable connector especially the "NEGATIVE" cable which needs to be checked at "BOTH" ends.
3. Battery voltage, must be 12.5 volts or better, voltage from the battery to the main circuit breaker to the ignition switch to the security/ignition fuse to the TSM/TSSM module to the engine stop/run switch to the starter button to the starter relay to the green wire that connects to the starter solenoid must not drop more than 1/2 volt of battery voltage.
4. Disconnect spark plug cables, with a voltmeter connected to the battery, the ignition switch in the on position, the kill switch in the run position, the starter button depressed, starter engagement should not bring voltage below 9.6 volts DC. If the voltage is below 9.6 the battery is faulty and must be replaced. I "HIGHLY" recommend a maintenance free AGM battery typically they have more amperage for cranking.
5. Faulty starter relay, check continuity.
6. Faulty starter solenoid, check contact plate and shoes for excessive electrical erosion/etching, refurbish as necessary or invert contact plate and use the virgin backside. Check contact shoes for being loose. Replace solenoid if the negative function is still a final outcome.
7. Faulty starter, bench test starter with a 12-volt battery if negative function check, decontaminate and undercut armature commutator segments as necessary, check segments with an ohmmeter probe each one and the segment next to it for shorts. Have the armature tested with a growler and field coils, and brush plate with an ohm-meter for opens, shorts or grounds. Replace brushes if less than .438" It is generally cheaper to overhaul/refurbish a starter motor than buying a new one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.fireblades.org/forums/honda-cbr-600/90605-bike-wont-start-makes-clicking-sound.html
wont start just clicks help
http://www.family-motorsports.net/GY6-50cc-150cc.pdf
https://www.partsfish.com/page/oem-parts-for-honda
http://absolutelyscooterparts.net/pdf/CGEN_dawg_scooter_manual.pdf

Sep 22, 2011 | Honda Motorcycles

1 Answer

1996 Kawasaki ZX-9R Ninja will not start just clicks


Hi, Careskawi02 you turn on the ignition switch press the starter button and all you get is the dreaded "CLICK" or "CLUNK" now before testing any electrical component in the Starter System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries. Depending on battery voltage starter relays and starter solenoids can make the same noise when you hit the starter button. You can easily determine which one is at fault by the following two simple tests:
STARTER RELAY- place your thumb and index finger on the starter relay and press the starter button, if you feel the click then the relay is faulty and needs to be replaced.
STARTER SOLENOID- bridge the positive and negative poles of the solenoid with a small screwdriver if you get a loud clunk then the solenoid needs to be rebuilt or replaced as necessary. If the engine turns over then replace the starter relay otherwise the usual suspects for a faulty starter solenoid are:
1. Battery terminals have loose or corroded connections.
2. Battery cables faulty due corroded or broken internal wiring at the cable connector especially the "NEGATIVE" cable which needs to be checked at "BOTH" ends.
3. Battery voltage, must be 12.5 volts or better, voltage from the battery to the main circuit breaker to the ignition switch to the security/ignition fuse to the TSM/TSSM module to the engine stop/run switch to the starter button to the starter relay to the green wire that connects to the starter solenoid must not drop more than 1/2 volt of battery voltage.
4. Disconnect spark plug cables, with a voltmeter connected to the battery, the ignition switch in the on position, the kill switch in the run position, the starter button depressed, starter engagement should not bring voltage below 9.6 volts DC. If the voltage is below 9.6 the battery is faulty and must be replaced. I "HIGHLY" recommend a maintenance free AGM battery typically they have more amperage for cranking.
5. Faulty starter relay, check continuity.
6. Faulty starter solenoid, check contact plate and shoes for excessive electrical erosion/etching, refurbish as necessary or invert contact plate and use the virgin backside. Check contact shoes for being loose. Replace solenoid if the negative function is still a final outcome.
7. Faulty starter, bench test starter with a 12-volt battery if negative function check, decontaminate and undercut armature commutator segments as necessary, check segments with an ohmmeter probe each one and the segment next to it for shorts. Have the armature tested with a growler and field coils, and brush plate with an ohm-meter for opens, shorts or grounds. Replace brushes if less than .438" It is generally cheaper to overhaul/refurbish a starter motor than buying a new one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1996 Zx9 won start won crank just makes clicking noise ZX Forums
Clicking but won start KawiForums Kawasaki Motorcycle Forums
Kawasaki Ninja ZX 9R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Feb 17, 2011 | 1996 kawasaki ZX-9R Ninja

1 Answer

No start problem on 07 883 customer sportster. When I hit the starter it either starts or when it does not start you can hear a click like a relay switch. 3 moths ago harley dealer replaced a relay do to...


You need to determine if the solenoid is delivering power to the starter motor terminal when it just clicks. You need to have either a test light or a voltmeter to read 12 volts DC. If, when it clicks, and the meter shows 12 volts at the starter terminal, then the starter motor is in trouble (it could be bad brushes or an open segment on the armature commutator). If you see no voltage, then check the battery side of the solenoid to see if the normally present at all times 12 volts disappears when the starter is tried. If that is so, check the battery cable for a bad wire or connection all the way to the battery. If it stays 12 volts, then the solenoid is bad and should be replaced. Hope that gets you started!

Sep 26, 2009 | 2007 Harley Davidson XL 883 Sportster

2 Answers

1990 1200xl sport not starting


Is the clicking noise coming from the starter? If it is I would say your bendix is shot and needs to be rebuilt.

Apr 28, 2009 | Harley Davidson XL 1200 S Sportster Sport...

Not finding what you are looking for?
2003 Harley Davidson FLHT Electra Glide Standard Logo

212 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4825 Answers

Mike

Level 3 Expert

4348 Answers

yadayada
yadayada

Level 3 Expert

79186 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...