Question about kawasaki ZX-6R Ninja Motorcycles

Open Question

How do i change a front indicator bulb on a kawasaki zx6r

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 132 Answers

SOURCE: I want to chang the horn in my kawasiki ninja zx6r

the horn is only held on by 1 bolt,undo this and remove the 2 wires then just reverse these steps to refit

Posted on Jun 13, 2009

  • 126 Answers

SOURCE: brakes will not bleed up on front of kawasaki zx6r

Keep bleeding and ensure that you keep brake fluid level in reservoir high. It is time consuming but it can be done. Just don't let reservoir go dry or you will have to bleed all that air thru lines.

Posted on Oct 11, 2009

  • 124 Answers

SOURCE: help channging the front wheel on a kawasaki ninga

By "changing the front wheel" do you mean how do you remove the wheel from the bike? If so, Start by securing the motorcycle in a upright position and place a jack under the engine with a wood protector between the jack and engine. Raise the motorcycle until the front tire is just touching the ground. Remove both brake calipers then loosen and remove the axle nut. Now remove the axle clamp and slide the axle out of the wheel. Note how the speedometer gear is mounted before pulling the axle. Now raise the motorcycle until the tire assembly will clear the fender. Reassembly is exact reverse of removal with the exception of when you install the axle you will tighten the axle nut before you tighten the axle clamp.

Posted on Nov 20, 2009

DoubleClutch
  • 376 Answers

SOURCE: iol pressure lite on kawasaki zx6r f1

Did you cahnge the filter also? Have you ran the motor to build pressure and fill the oil filter. The light should go out when the oil gets pumped threw the filter and engine.

Posted on Nov 29, 2009

Jetskidoc
  • 72 Answers

SOURCE: how do i remove the coil to change my spark plugs

Those are stick coils, just unplug the connector at the top pf the coil and then they just pull out, there is rubber around the coils and sometimes they want to stick in the hole, just give them a pull, you can spay a little window cleaner on them when you put them back in, so they slide eaiser.

Posted on May 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does a US ecu for a zx6r 636 2005 work on an Australian zx6r 636 2005


Hi, Chris after careful deliberation 4 out 5 Kawasaki Gods give this one a thumbs up, but just to be on the safe side you should give your local dealer's parts/service department a call to confirm. For more information about your question and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
05 ecu problem need 06 ecu
http://support.bazzaz.net/service_manuals/ZX636C1_C6.pdf
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Dec 31, 2016 | 2007 kawasaki Ninja ZX6R

1 Answer

I have a 06 zx6r 636 Kawasaki Ninja, went out to start my bike and the turn signals won't work.Front or back , recently installed new blinkers. Looks like hazards are on, with no blinkers or lights


Hi, Anonymous if you installed LED lights for blinkers you need to install turn signal load equalizer to compensate for the lower wattage bulbs you may want to contact the manufacturer of the LED lights as different options are available but can be more time consuming and difficult to install load equalizers are plug n play for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. For more information about your issue please visit the website below. Good luck and have a nice day.
Motorcycle Parts Accessories
http://service.tanga-moteurs.ro/data/Kawasaki%20Ninja%20ZX6R%202005-2006%20Service%20Manual.pdf
Owner Manuals Service Manuals Kawasaki Vehicles

Dec 24, 2015 | kawasaki Motorcycles

1 Answer

Headlights on 2004 Kawasaki zx6r will not come on.


If the tail light comes on , then it may be the headlight bulb,so try with high and low beam
if the tail light bulb doesnt come on, then it can be a fuse, relay, switch block, ignition switch, broken wire, bad corrector and the list continues, so it is out with the multi meter and test light and some electrical knowledge to track it down.

Mar 05, 2011 | kawasaki ZX-6R Ninja Motorcycles

1 Answer

Could you the tyre pressures front and rear for a kawasaki ninja 600 year 2000 please .thanks


hi, in there wisdome kawasaki played around with tyre sizes on the zx6r ninja,

tyre size rear 160/60/17.
tyre size front 120/60/17 1995-98 models zx600f

rear. 170/60/17
front 120/60/17 1998-2000 models zx600-g1

rear 180/55/17
front 120/65/17 2000-01 models zx600j

the only thing they didnt play around with is the tyre pressures all models front 36psi or 2.5 bar
rear 41psi or 2.9 bar

hope this helps and thanks for using fixya.
paul

Jan 30, 2011 | kawasaki ZX-6R Motorcycles

2 Answers

Wiring diagram 2001 zx6r


Try this manual, it should cover all your needs. Are you sure you have the correct rating fuse in the box, the manual will solve the problem any way. Good luck:

http://vitek.vellum.cz/manualy/Kawasaki%20Ninja%20ZX-6R%2000-02%20Service%20manual.pdf

Jan 29, 2010 | 2001 kawasaki ZX-6R Ninja

1 Answer

How do i replace front indicators on 2000 zx6r. I don't know how to get the old one off without removing the air filter. Is there an easier way?


There is a small 2 pole connector that lives between headlight and air intake for each side. If you can reach this plug and undo it then prise the indicator off the fairing. Or take the front fairing off the bike and do it with ease

Oct 23, 2009 | 2000 kawasaki ZX-6R Ninja

2 Answers

1996 zx6r


Actually u can reach in and just pull the 3 prong connector right off of the bulb.Then pull off the rubber cover with the tab that is at the top of the circular rubber cover. The bulb is held in by a small wire that hooks on both sides. Replace the bulb and reverse the steps.There is no need to remove any fairings to replace the bulb.

Sep 10, 2009 | 1996 kawasaki ZX-6R Ninja

1 Answer

I want to chang the horn in my kawasiki ninja zx6r


the horn is only held on by 1 bolt,undo this and remove the 2 wires then just reverse these steps to refit

Jun 10, 2009 | 2001 kawasaki ZX-6R Ninja

1 Answer

Zx6r fuel tank


search google for kawasaki forums. you should join one or two and ask the same question. Someone there, who has direct experience, will know if it fits or not.

Apr 30, 2009 | 1997 kawasaki ZX-6R Ninja

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...