Question about Harley Davidson FLSTC - FLSTCI Heritage Classic Motorcycles

1 Answer

When I try to start my new FLSTC I get power into the run button but when I hit the start button nothing happens. I have to try 3-4 times before start

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

Look at the end of the starter for a single wire that plugs onto the starter just above the five sided plate, green or green/white colored wire. Unplug the wire and connect a test light or a volt meter to the wire. Turn on the ignition switch and press the start button. The test light should light up or the meter should show battery voltage. If not, your starter relay is probably bad. They are usually located on the mud shield on the lower part of the rear fender. It's a one inch plastic cube. For some reason, these give a bit of trouble on the Softail series bike. I think it's due to where they are mounted. If you're hearing a loud click but the engine is not turning over, it's the contacts in the starter solenoid. Remove the 5-sided plate and take the plunger and spring out. Look at the two large copper contacts inside the solenoid. If they are badly burned, they should be replaced. This can usually be done without removing the starter. Parts are available through H-D dealers or aftermarket sources.

Good Luck
Steve

Posted on May 23, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

MacBook Pro no power at all


When my Mac decided to no work when power button was hit, only two options came to mind, Power Button or Motherboard.
Turns out, power button is connected to keyboard which was the problem. The fix was easy, new keyboard.
Hope this helps.
Cheers

Feb 08, 2014 | Apple Computers & Internet

1 Answer

Intel D946GZIS machine will not start after being reassembled. The green light on the Motherboard is on but after hitting the power button nothing happens


It is more than likely the power supply that is faulty. Newer PSU's have a 5volt supply missing, this means that some older boards will not run with the new PSU's. Try and find an exact match for your older supply but with a better power rating, if that is what is required.

Jun 24, 2012 | Intel D946GZIS Motherboard

1 Answer

Put the run button on and hear a click from the start relay. Hit the start button and nothing at all. Dead silent.


The click you are hearing is not coming from the "starter relay". The starter relay is activated by the "start" button only. The relay you're hearing is from the ECM or the securtiy system and that's what has your bike "dead in the water". I'm sorry but I know nothing about either system.

Good luck
Steve

Oct 02, 2010 | 2000 Harley Davidson FLSTC Heritage...

1 Answer

I went to start my 1997 HD FLSTC. It turned over


ignition switch common for your bike less expensive aftermarket but do make sure to solder in new connector at the same time

Sep 20, 2009 | Harley Davidson Harley-Davidson Motorcycle...

1 Answer

Electical short, bike wont start


When you shorted with tool you may have caused a wire to burn through insulation to ground? You could try to disconnect wiring until sparking stops.

Jul 27, 2009 | 2003 Harley Davidson FLSTC Heritage...

1 Answer

Kitchenaid kudso1dlss3 clean light flashing cannot do a new cycle


I do not have the same model as you, my model is KUD01ILBS6 but I have the same problem. A service tech told me it was a error code and here is how to fix it.

1 open the dishwasher door
2 hit high temp scrub button
3 then hit energy saver dry button
4 do step 2 & 3 again
5 close the door
6 hit the cancel button
7 you can hit cancel button again then try to start your dishwasher

This works for me, you may have to do this every few months because there is a glitch in kitchenaid where if the water temp is not sensed right it will keep the dishwasher from working. It took me 3 service calls to find this out.

Jan 17, 2009 | KitchenAid 24 in. KUDI01FLSS Stainless...

1 Answer

Fails to start


the problem is your fan may not have got proper power supply....the wire connecting the fan and power chord should be perfect....if there is a loose connection your fan may not get proper power supply and then it will not run.....this is the main probem.....just check the wire connection between the fan and power chord has been properly connected and there are no loose connections....i am a software engineer....and have experience in it....try this ...it will 100% solve your problem.......

Sep 19, 2008 | ASUS P4P800 SE (890552603657) Motherboard

2 Answers

Rca 61 inch projection tv model D61W20


Steve,
I have the exact same problem with my tv. same model. If you happen to find a solution, could you please forward it to me. I will be very appreciative. email me at jjkjjk13@hotmail.com . I'll do the same for you if I find a solution.

Jan 20, 2008 | RCA D61W20 61" Rear Projection Television

1 Answer

Sometimes comes on. most times doesn't come on


You need a new Battery. You said if you powered up on the plug its working right? So try to charge the battery like 30mins or so then try to power on to battery. If not get a new batt.

Aug 06, 2007 | Tomtom GO 300 GPS Receiver

1 Answer

Not starting up I get nothing!


Press the power button and hit the up button to reset to start.
I have the same issue and my palm battery will not charge and stil working on it. Try line 1 first
2nd option remove the battery and try without it. Then put the battery back in.
Hope this helps

Aug 07, 2006 | Sony CLIE PEG-SJ22 Handheld

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

188 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...