Question about Harley Davidson FLHT Electra Glide Standard Motorcycles

1 Answer

No power to brake light on a 95 FLH - FLHT Electra Glide Standard Harley Davidson Motorcycles

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,565 Answers

Check the rear brake light switch. To find it, find the metal brake line coming out of the rear master cylinder going to the rear brake. Follow this line and underneath the bike you'll find a tee fitting with a pressure switch. This is the rear brake light switch. With the ignition switch on, one of the lugs on the switch should have voltage on it. If not, trace the wire back to the switch looking for a break. If it does, the switch is probably bad but you should have a front brake light switch as well. It should work even if the rear switch doesn't. If this is the case, either the front switch is bad as well or you have a wiring problem going back to the rear brake light.

Good Luck
Steve

Posted on May 24, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn signal


DO YOU MEAN THEY ARE THERE BUT DON'T WORK OR THEY ARE NOT THERE AND YOU ARE INSTALLING THEM . IF THEY ARE THERE BUT DON'T WORK CHECK FOR POWER AT THE HARNESS TO THE LIGHT, NO POWER, CHECK THE SIGNAL STAT, IF YOU ARE INSTALLING THEM, THERE SHOULD BE A HARNESS SOMEWHERE CLOSE TO THE MOUNTING LOCATION.

Jun 08, 2013 | Motorcycles

1 Answer

95 mustange gt brake light dont work check #9 fuses change all bulbs replaced switch on brake pedal hazards lights works ,parking or running lights works,turning signal lights works,what other places i...


I assume the fuse has power if the hazards work.
The third brake light skips the turn signal switch, the regular brake light circuit goes thru the turn signal switch.
Do you have power going into the turn signal switch on the red lite green wire from the brake switch ?

Feb 17, 2013 | 1995 Ford Mustang

1 Answer

I have no stop light on a 1979 flh


Hi Peter, always check fuses and bulbs first for broken filaments. Then check the connection at the rear fender wiring harness, inspect for corroded, broken or loose pins. Use a dab of dielectric grease and repair as necessary. Check your brake relay if you have one , check your brake light switches for continuity, some models rear turn signals were single filament bulbs only, no running light. If all else fails get out your test light and start tracking the power wire from the harness connection. For a free wiring diagram please visit the website below and good luck:

May 19, 2012 | Harley Davidson Motorcycles

1 Answer

Where is my relay starter switch on my 2000 deuce


Well if like mine flh front of bat its with the brake relay they are attached to the frame my knolage is limited to flh 09 & 93...great place to ask is our forum ..you are invited...>> http://www.hdtalking.net/

Aug 17, 2011 | 2000 Harley Davidson FXSTD Softail Duece

1 Answer

Need diagram on how install rebuild kit in 1973 Harley FLH rear master cyclinder.


Take the master cylinder off the bike. There is a snap ring in the plunger bore of the master cylinder. Take the pieces out of the master cylinder and place them in a line in the order and direction that they came out. Hone or clean the bore of the master cylinder out and install the new parts back in the same way the old parts came out. It's not that difficult. There is one part, a valve, that goes in your master cylinder because you have a drum brake on the rear. If you had a later model with a disc brake, you would leave this part out. For a picture, go to Bike Bandit . com.
flh-80/o/m900#sch189918">http://www.bikebandit.com/1973-harley-davidson-flh-80/o/m900#sch189918

Good lLuck
Steve

Apr 27, 2011 | Harley Davidson FLHT Electra Glide...

1 Answer

Brake lights on 95 camaro


Check your brake light switch at your brake pedal make sure that you have power coming in and then going out with pedal depressed if that is ok check for a faulty turn signal switch the brake lights run thru the switch on the hazard circuit.

Apr 05, 2010 | 1995 Chevrolet Camaro

2 Answers

Why won't my brake lights come on and allow me to


check the fuse for your brake lights or the brake light switch,the inter lock solenoid on the shift cable reacts from the power at the brake switch.

Dec 29, 2009 | 1995 Lincoln Town Car

1 Answer

1993 Voyager break light on -no power brakes


spray some silicone underneath the brake peddle- way up in there. pump the brake a few times.
The thing up there gets stuck. Happens to my 95 van.

May 30, 2009 | 1993 Plymouth Voyager

1 Answer

Where is the brake light switch on a 95 dakota


The brake light switch is behind the brake pedal

Apr 03, 2009 | 1995 Dodge Dakota

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Mike

Level 3 Expert

4345 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...