Question about 2003 Suzuki AN 650 Burgman

1 Answer

How do I remove the seat and cover to 1. check water level in radiator or to add water.2. how do I access oil filter and to change oil 3. Access to change spark plug

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

You do not have to remove the seat. You will have to remove the covers on the "hump" to get to where you need to be. Not a big deal there. I reccomend going to YouTube and typing "Oil change Burgman 650". You will see several different vidios on how to perform the procedure and the supplies that will be needed. I also reccomend purchacing a Suzuki oil filter removal tool. It is well worth the six bucks to speed things up and prevent a OOPS that could cost you a lot of time and clean-up.

Posted on May 31, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do iremove oil pan 01 montecarlo


OIL PAN
Removal & Installation
1. Disconnect negative battery cable. Remove engine torque strut. Raise and support vehicle. Drain
crankcase. Disconnect oil level sensor electrical connector. Remove oil level sensor and oil filter.
Disconnect front exhaust pipe from manifold. Remove right front wheel and splash shield.
2. Disconnect oil cooler pipes. Disconnect A/C compressor electrical connector. Remove A/C compressor,
and position aside. Disconnect engine mounts from frame.
3. Remove flexplate access cover. Use transmission jack at transaxle to raise engine. Remove oil pan bolts
and oil pan. To install, reverse removal procedure. Install oil level sensor after oil pan is installed. Tighten
retaining bolts to specification. See TORQUE SPECIFICATIONS.

Sep 25, 2014 | 2001 Chevrolet Monte Carlo

1 Answer

Where is the full filter


I believe there is actually an access panel in front of the second row seat behind the drivers seat that you can access the top of the tank, fuel pump and possibly the fuel filter. Lift up the carpeting and check.
1. Remove the fuel tank cap to lower the fuel tank's internal pressure. 2. Locate access cover. 3. Remove the fuel pump & fuel filter assembly installation screws, then remove the fuel pump & fuel filter assembly from the fuel tank.



Mar 29, 2014 | 2004 Kia Sedona

1 Answer

Looking for information on 1988 honda vlx radiator


Instructions
    • 1 Remove the motorcycle's carburetor and clean it with carburetor cleaner, getting rid of any and all grime and deposits within. If necessary, use an air compressor with a small tip to blow out any clogged lines within the carburetor.
    • 2 Check the motorcycle's fuel tank for old fuel. Drain the fuel tank completely and refill the tank with fresh fuel. Old gasoline isn't good for most motors, especially older ones.
    • 3 Remove the motorcycle's seat by unscrewing the two mounting bolts on both sides of the back of the seat with a 12 mm socket wrench. Pop off the top of the air box and remove the bike's air filter. Clean this thoroughly in hot, soapy water. Rinse it off, let it air-dry then apply air filter oil before reinstalling it in the motorcycle.
    • 4 Check the tire pressure and integrity of both tires on the motorcycle. If either tire is flat, leaking air or overly worn, replace the tire and tube.
    • 5 Change the motorcycle's oil. Warm the bike up, then remove the oil drain plug underneath the transmission and drain the oil. While the drain plug is still loose, fill the oil reservoir until oil begins to run out of the plug. This means the reservoir is full. Tighten the drain plug.

Jan 20, 2013 | Honda VT 600 C Shadow Motorcycles

1 Answer

How do i change the water pump belt on a 2001 Cadillac Deville .


2001 Cadillac Deville 4.6L SFI DOHC 8cyl Removal & Installation procedure...

1. Before servicing the vehicle, refer to the Precautions section.
2. Drain the coolant.
3. Remove or disconnect the following:
Negative battery cable
Upper fill panel, if equipped
AIR injection control valve, if equipped
Air cleaner
Oil level indicator tube nut, if necessary
Water pump belt cover
Water pump drive belt
Lower radiator hose
Thermostat bypass hose from the coolant inlet housing
Water pump cover

4. Remove the water pump by rotating it clockwise using special Tool J 38816-1A (water pump remover/installer).

To install:

1. Install the water pump with a new O-ring, by turning it counterclockwise using the special tool, until it stops. Torque the water pump to 73 ft. lbs. (100 Nm).

  1. zjlimited_842.jpg

Fig. To ensure proper operation, be sure to install a new O-ring (click for zoom)

2. Install or connect the following:
Water pump cover. Torque the bolts to 89 inch lbs. (10 Nm).
Lower radiator hose
Thermostat bypass hose to the coolant inlet housing
Water pump drive belt
Water pump belt cover
Oil level indicator tube nut, if necessary
Air cleaner
AIR injection control valve, if equipped
Upper fill panel, if equipped
Negative battery cable

3. Refill and bleed the cooling system.
4. Run the engine and check for leaks.


Hope this helps (remember to rate this comments)

Mar 10, 2011 | 2001 Cadillac DeVille

1 Answer

WHERE IS THE FUEL FILTER LOCATED FOR THE SEDONA 2004


believe there is actually an access panel in front of the second row seat behind the drivers seat that you can access the top of the tank, fuel pump and possibly the fuel filter. Lift up the carpeting and check.
1. Remove the fuel tank cap to lower the fuel tank's internal pressure. 2. Locate access cover. 3. Remove the fuel pump & fuel filter assembly installation screws, then remove the fuel pump & fuel filter assembly from the fuel tank.

Nov 29, 2010 | 2004 Kia Sedona

1 Answer

I want to check the engine oil level for previa 2.4 petrol 1995



OIL LEVEL CHECK Every time you stop for fuel, check the engine oil as follows:
  1. Park the vehicle on level ground.
  2. When checking the oil level it is best for the engine to be at operating temperature, although checking the oil immediately after a stopping will lead to a false reading. Wait a few minutes after turning off the engine to allow the oil to drain back into the crankcase.
  3. Open the hood and inspect the level of the engine oil tank. The fluid level on the tank should read between FULL or F and LOW or L.
  4. If the level is below the LOW or L line, remove the cap and add enough engine oil to reach the FULL or F line. Fig. 1: Fill the engine oil tank located under the hood first 90911p07.jpg
  5. Install the oil cap and hand tighten.
  6. After filling the oil tank, remove the engine access hole cover on the drivers side. Fig. 2: Make sure the oil tank is to the F mark 90911p15.jpg Fig. 3: The oil dipstick is located under the driver's side engine access hole cover 90911p83.jpg Fig. 4: Place your finger through the hole and pull straight up to remove 90911p84.jpg
  7. Remove the engine oil dipstick and wipe it clean.
  8. Reinsert the dipstick, push it in as far as it will go, the pull it out and look at the level on the end.
  9. If necessary, insert more oil through the oil filler cap next to the dipstick, this will completely top off the system. Fig. 5: The oil dipstick has two markings for level check 90911p85.jpg Fig. 6: To fill the crankcase, remove the engine oil filler cap 90911p86.jpg prev.gif next.gif

Nov 06, 2010 | Toyota Previa Cars & Trucks

2 Answers

Oil & coolant change, 1998 yamaha 1300 royal star


Before doing either of these jobs, you'll have to run the engine for 8 to 10 minutes to warm up the engine, oil and water.

To change the oil - prop the motorcycle so that it's as close to level as possible, but will not tip over in either direction. Remove the oil fill cover on the back crankcase cover on the right (brake pedal) side. Look directly beneath the cylinders, you'll see a large hex-head bolt (drain plug) in the center of the crankcase. Make sure that you have a container with a capacity of in excess of one gallon under the bolt. Loosen and remove the drain plug (very quickly, the temperature of the oil will be sufficient to cause blisters if permitted to remain on the skin), but do not, if possible, allow it to fall into the pan. Permit the oil to drain fully; while it's draining, clean the plug carefully - you'll find a magnet protruding from the center of the plug, with metal filings collected on the surface - remove as many as possible before reinstalling.

Turn the plug back into the crankcase until oil ceases dripping, move the pan to the front of the engine. Behind the radiator, low on the front of the crankcase, you'll find the filter - it looks very much like the filters you're used to seeing in your car. If you're at the front of the bike, turn the filter counterclockwise to loosen and remove; remember that the filter holds about a half-pint of oil as hot as that you drained out of the crankcase, so keep your hands out of the way as much as possible. When the oil stops dripping, and the filter has been removed and disposed of, put a thin film of oil on the rubber ring on the bottom of the new filter, turn it clockwise to mount it on the crankcase, and tighten as firmly as you can with your hands.

Go back to the drain plug, remove and let whatever oil has collected drain out, then reinstall, tightening to 32 ft.-lbs (43nm).

Pour about 3 1/2 quarts of oil into the crankcase, replace the oil fill cover, start the engine and check for leaks at both the drain plug and the filter, tighten as necessary. To check the oil level, look for a glass window on the right side of the crankcase marked for high (max) and low (min) levels. Get on hands and knees and look under the front crankcase cover directly beside the right operator's footrest; you'll probably need a flashlight to read it. Once the oil level is between the minimum and maximum markings, tighten the oil fill cover, and return the bike to its' normal parking position on the kickstand.

To change the coolant - remove the driver's seat, fuel tank, all four cylinder side covers, and the right side cover (color-matched cover under driver's seat). Prop the motorcycle so that it's as close to level as possible, but will not tip over in either direction. Place a 24"-30" drain pan slightly forward of the center of the engine - if you do not have a large drain pan, a small one placed under the drains individually, IN THE ORDER LISTED, will work. Siphon all coolant from overflow reservoir under the side cover OR remove the center cover, remove bolts holding the reservoir to frame, invert the reservoir to empty, and reattach the reservoir to the frame.

Now, remove the radiator cap and the drain plug at the bottom of the radiator, allow the radiator to empty. Remove the plugs at the lower portion of each cylinder in no particular order, drain fully, then remove the drain plug from the bottom of the water pump (the large protrusion beside the front right driver's footrest). Once all drains have ceased dripping, reinstall the radiator plug (torque to 18 ft.-lb., 25nm), all four cylinder plugs (seat firmly in the drain holes), and the water pump plug (torque to 32 ft.-lb., 43nm). Fill the reservoir in the rear, then fill the radiator as much as possible, cap, and run the engine for 3-5 minutes to warm. Remove the radiator cap, check the radiator and refill, repeating until there is no air beneath the radiator cap when it is removed.

Reinstall the body panels, tank and seat, and return the bike to its' normal parking position on the kickstand. If additional coolant is needed it will be added to the reservoir - check frequently for about the next 100-150 miles.

Note on oil - I've always warned people away from oils that were labeled "energy conserving", but lately I've noticed that those same oils no longer carry that label. I've been seeing a new seal on them; on the outside of the seal are the words "American Petroleum Institute" on the top, "Certified" on the bottom, and in the center of the seal are the words "For Gasoline Engines", and - surprise, surprise! - they ALL contain molybdenum disulfide, the stuff that makes clutches slip. Check the bottles of the oil that you're considering for use in your motorcycle. If you see the API seal, keep going. Unfortunately, a member named "rasolheim" is learning the hard way how expensive an error like that can be; I hope that I can warn others before they make the same mistake.

Note on coolant - using an "extended-life" coolant makes good sense; it'll extend the interval between coolant changes and do a better job of protecting the aluminum cylinder block and heads. It does NOT, however, free you from the responsibility of checking the coolant level and color frequently. Periodic checks (I do it every day, before and after a ride) are your best protection against leaks and corrosion.

Jul 25, 2010 | 1998 Yamaha Royal Star XVZ 1300 A

1 Answer

Oil change


There are forums that will give you step by step instructions on how to do it if you Google it.You may also find a free service manual online.
I have a 1600 in my shop now and you have to drain the engine ,change the oil filter and drain the oil tank,fill the tank with 2 quarts oil,run engine for 15 seconds,add 2 more quarts oil ,run bike for 30 seconds then check oil level in the tank and adjust level if needed.
May also need special wrench to remove filter.

Oct 24, 2009 | 2001 Yamaha V Star 1100 Classic

1 Answer

How to change the fuel filter for 2004 kia sedona


I believe there is actually an access panel in front of the second row seat behind the drivers seat that you can access the top of the tank, fuel pump and possibly the fuel filter. Lift up the carpeting and check.
1. Remove the fuel tank cap to lower the fuel tank's internal pressure. 2. Locate access cover. 3. Remove the fuel pump & fuel filter assembly installation screws, then remove the fuel pump & fuel filter assembly from the fuel tank.

Jul 02, 2009 | 2005 Kia Sedona

2 Answers

How do you change the oil filter on a Hyundai Accent 1998/99?


Replace the oil filter after draining the old oil, and" BEFORE "adding new fresh oil, otherwise you'll be dump all that fresh oil, on the ground,while you "TRY to get the new filter installed.

Step 1 Remove drain plug,Drain oil into drain pan
Step 2 Remove oil filter
Step 3 Reinstall drain plug,qnce oil has drained.
Step 4 Fill new filter with oil,lube seal on filter.
Step 5 Install new filter, Add fresh oil to proper level.replace filler cap
Step 6 Run engine check for leaks.
Happy motoring!

May 23, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
2003 Suzuki AN 650 Burgman Logo

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...