Question about Zongshen Aerox Race Replica Motorcycles

1 Answer

Rear break assembly - Aerox Race Replica Zongshen Motorcycles

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 496 Answers

Not sure what it is that you need help with please tell me more and i'll be happy to help
M.Woodring

Posted on May 23, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change front wheel bearing on 2006 volkswagon jetta statonwagon


Remove wheel. remove the drive shaft. remove the break caliper and set to the side. Remove the break disc and the backing plate. At the rear of the hub there are 4 size 16 multi inhex bolts, remove these and the wheel bearing assembly will come out( may need a small tap to loosen). assemble in reverse order.

Oct 15, 2014 | 2006 513253 VW Jetta Front Wheel Bearing &...

1 Answer

Rear brake light out


First of all check the brake light fuse on the fuse box marked brake/rear lights.
Please use the voltmeter range in your multimeter to check for the voltage on your rear light assembly while the brake pedal is kicked. If there is supply then the lamp is faulty , the ground to the lamp assembly is faulty. remove the assembly and check holder of lamp .
If there is no voltage then the brake fluid pressure switch is faulty or there is break on the wire to the switch or to the rear assembly.

Jan 22, 2011 | 2008 Mazda Mazda3 Hatchback

1 Answer

How do I replace the tail light assembly on a 2003 hyundai santa fe?


You'llhave to raise the rear compartment door fully. Next locat the tailight you wish to replace or same if you are replacing one of the tailigt bulbs. This would include the stop bulb or turn signals etc.
Next there is a black plastice side panel located between the lamp assembly (the entire plastic housing) and the inner portion of the rear compartment door. There you'll see two phillips head screws which you must remove. This releases the entire assembly.
You then next gently give it a small tug toward the left (if a left side assembly) or to the right if other wise. What happens there is that there is a stud that's held pretty snuggly by a modled ring in the body assembly. Don't twist the lamp assembly up or down unless you want to break this off but give it a slight pull outward. Then you're done. The entire assembly will be released and you'll be home free for changing any of the bulbs or even replacing the entire assembly. W/o breaking it of course.

Jul 15, 2010 | 2003 Hyundai Santa Fe

1 Answer

Rear drum brake assembly


google rear break drum

Aug 29, 2017 | 1993 Ford Econoline

1 Answer

How do i pull off the lens for rear break bulb to replace the blinker and the break bulb?


Open the rear gate. There are a couple screws you need to take out to remove the whole lamp assembly. Pull the bulbs out and replace then replace the lamp and put screws back in.

Nov 09, 2009 | 2008 Hummer H3

2 Answers

1998 S10 rear break lights and blinkers do not work.


If the fuses or brake light switch were bad your third brake light would not work same with the multi purpose switch. you either have a wiring problem like some broken wires or the actual light sockets are bad. it is common with gm trucks that the circuit board for the tail lights melts and does not make contact.

Nov 02, 2009 | 1998 Chevrolet S-10 Pickup

1 Answer

Replace right rear break light


PLEASE DON'T FORGET TO RATE!!!

Signal & Marker Lights Removal & Installation Rear Lamp Assembly Sedan To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the luggage compartment quarter trim panels.
  3. Disconnect the rear lamp assembly electrical connector.
  4. Remove the lamp assembly mounting nuts.
  5. Pull the lamp assembly away from the body.
  6. Disconnect the rear lamp assembly bulb connectors.
  7. Remove the rear lamp assembly.
6753524.gif
To Install:
CAUTION
To prevent water from entering the luggage compartment, make sure the rubber grommet is fully seated.
  1. Position the rear lamp assembly near the body and connect the bulb connectors.
  2. Install the lamp assembly into the body.
  3. Install the lamp assembly mounting nuts. Tighten to 53 in-lbs (6 Nm).
  4. Connect the rear lamp assembly electrical connector.
  5. Install the luggage compartment quarter trim panels.

Jul 16, 2009 | 1998 Ford Taurus

2 Answers

How do you access the rear tail light bulbs to replace in a 2006 sienna van?


2006 Sienna taillight.
Open tailgate. Loosen bolts holding tailight assembly. Standing next to the car, pull light assembly toward the side and back of the car. It will feel like you're going to break the light assembly, but you won't. I attempted this last fall (2008), but feelin' a bit uncomfortable pulling on it in different directions, I reassembled it and had the guys at the dealership do it right there in the dealership parking lot. If it was to break, I wanted them to break it! But it didn't break and I saw how to do it next time.

Jul 14, 2009 | 2008 Toyota Sienna

1 Answer

2003 Dodge Durango Rear Brake Assembly


could be the shoes have come off their backing... could be loose or worn hardware

Jan 21, 2009 | 2003 Dodge Durango

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zongshen Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Francisco Padilha
Francisco Padilha

Level 2 Expert

81 Answers

Joseph Hoffmann

Level 3 Expert

1709 Answers

Are you a Zongshen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...