Question about 1989 kawasaki GPX 250 R

1 Answer

I have a kawasaki250gpx when i start it up its ok on throttle but when it gets warm and i take throttle of it high revs first then it will die on tick over

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 105 Answers

Need to clean carbs Also clean gas tank MOPAR KENNY

Posted on May 22, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Saw starts but after it warms up it revs uncontrollably at high rpm's, wondering if the seals or rings may e gone?


Seals and or rings would not make the saw rev high. More likely the throttle is sticking open after it gets hot. Check throttle position and clean. Get a can of spray carb cleaner from auto parts or the marine store. Spray away till it's clean and check the throttle position again. RPM's only go up for two reasons, and they are both fuel air ratio. One is the throttle is open the other is momentary rev when the fuel supply is cut off.

May 26, 2015 | Echo CS400 18" Chain Saw

1 Answer

Problem with my fzr after first ride in the morning iit wants to die wen taking off an most of the time it will then start it an it wont rev if let throttle go it will die


I'll tell you why. It is cold natured. I have a 89' Virago, and it doesn't like going anywhere till' it is warmed up. I usually just set the choke up a bit for about 5 minutes, and then hop on and go.

Apr 15, 2013 | 1988 Yamaha FZR 250

1 Answer

50cc Scooter won't rev up, Keihin PD18J carb


my 50cc scooter will idle at first and rev very well but wont idle what can this be

Jul 08, 2012 | Motorcycles

2 Answers

Atv hanging idle


check your float height? sounds like its high and runs normal when cold like the choke is on but when warm its getting too much fuel.

Apr 20, 2017 | Honda 2004 FourTrax Foreman ES

3 Answers

MY vehicle starts to die after it gets warm


Had the same thing happen to me. After it warmed up it would die check diffent things on it. Had the pump tested after it was warm not much pres. Change pump and good to go.

Feb 18, 2010 | 1986 Ford Crown Victoria

1 Answer

90 Cherokee Laredo 4.0 Replaced the throttle body, and fuel pump. When it starts it revs up to 2100 RPM's then dies.


Fuel system should be ok. check for air leaks around throttle body, make sure TBI gasket or o-ring are not sucking air which will cause high RPM's, also check for vaccum leaks.

Nov 16, 2009 | 1990 Jeep Cherokee Limited

1 Answer

Idle speed engine dies when throttled


It does sound like its getting to much fuel, or the lack of air. Air filter ok? If it is you might need to have a compression check done to see how the piston rings are.

Jul 03, 2009 | 2001 Honda XR 250 R

1 Answer

Rough running kawasaki


you need to let it warm up before beating on it. inline 4s are always cranky when cold. another issue could be dirty carbs and clogged carb jets causeing it to run extreemly lean, rev high and die out. pulling 4 carbs isnt "fun" but you could do it in an afternoon.

Mar 07, 2009 | 1995 kawasaki ZX-6R Ninja

3 Answers

Ryobi 31cc lawn trimmer carb adjustment


As with all 2 strokes if you have compression and a reasonable spark, you only need fresh fuel with correct oil ratio) and they must go !(as long as you haven't fiddled first and all gaskets are sealing) I start mine by(1) pumping the primer till it is firm,(2) full choke,(3) pull till it kicks ONCE,(4) half choke, pull till it runs,allow to warm up and(5) switch to run (you may need to apply a bit of throttle while pulling as in (4)(or give it a few more pumps if it dies) If all is ok, check that when properly warmed up there is a smooth transition from idle to full revs, if it hesitates it may need the LOW SPEED mixture leaning (clockwise) SLIGHTLY.If it dies the LOW SPEED mixture may need richening(anti-clockwise)(adjust 1/8 turn at a time) Make sure that motor is just peaking at full revs and is on the RICH side of peaking (HIGH SPEED mixture)(this will avoid seizing it Adjust both till it revs cleanly and is JUST rich at full, and idleing nicely and it should start without too much trouble.(If you have fiddled and are lost,-about 2 1/2 turns out from closed on both needles should get you started)

Nov 23, 2008 | Garden

Not finding what you are looking for?
1989 kawasaki GPX 250 R Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...