Question about Harley Davidson FXDWG Dyna Wide Glide Motorcycles

1 Answer

Starter engages when you turn switch on - FXDWG Dyna Wide Glide Harley Davidson Motorcycles

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 70 Answers

Check the start button for shorting, and the wiring on the starter to see if it is correct.

Posted on May 22, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram 1999 buick century. Starter engages when battery cables are bolted to battery.


-the wires are not correctly re-installed for the starter.
- u may need wiring diagram
Did you take pictures before you took it apart, or did you tag wires before unconnecting them.

Mar 12, 2015 | 1999 Buick Century

1 Answer

What couse the STARTER TO STAY ENGAGED


You don't say whether the starter is continuously cranking the engine or just spinning continuously or whether after starting the engine the starter switches off but remains engaged? Lack of detail makes it difficult to give anything but a general answer.

Certainly the starter should be removed and checked for damage and correct operation. The pinion might be tight on the helix, the solenoid could be tight, the return spring broken or the arm pivot seized. If the starter has been engaged while the engine has run at speed or for more than a few minutes the overrun clutch should be replaced.

In any case where the starter has remained engaged the ignition/starter switch and the drive mechanism in the steering column lock should be inspected for correct operation.

Mar 01, 2015 | Chevrolet 1500 Cars & Trucks

1 Answer

1972 FLH. When ignition is turned on starter


solenoid likley. Pull off the small 50 wire and if it still runs it is the solenoid. If not could be the starter relay

Oct 02, 2014 | Harley Davidson Motorcycles

1 Answer

Turn the key to start-can hear switch engage but either hesitates before starter engages or does


How old is the Jeep? Most likely either the starter has a bad solenoid or there is a corroded/ loose connection between the battery and the starter.

Mar 06, 2014 | Jeep Cars & Trucks

1 Answer

Car won't engage starter


At the starter relay, you have two red or purple wires, one goes to the starter and the other comes from a 30amp fuseable link. Is that fuseable link circuit hot ?
From the key switch, power goes thru the alarm relay, then the clutch safety switch or automatic selector switch, then to the starter relay. The fourth wire on the starter relay is a ground.
You should be able to put power to the starter relay on the white or yellow wire coming from the safety switch to make the relay engage.
My guess is something wrong with the alarm system.

Mar 02, 2014 | 2004 Hyundai Tiburon

1 Answer

Starter wont engage


Could be the switch, the solenoid, or the starter. You would need to check for power at the starter post each time the key switch is in the start position. You can hook up a test light or a meter to watch it.

Jul 08, 2013 | Ford Mustang Cars & Trucks

1 Answer

Turn switch on and all the lights work but the starter wont engage


If the starter wont turn...Id check / replace starter solonoid.
If the starter turns but doesn't engage the flywheel...I'd check / replace the bendix.
If starter checks good and bendix is good...I'd look at the teeth on the flywheel.

Hope this helps...

Jul 23, 2011 | 2005 Jeep Wrangler

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...