Question about 2007 Suzuki Boulevard C50

1 Answer

Driving down the road a open the throttle to accelerate. the engine revs up but it takes the bike a few seconds to speed up. could it be clutch fluid? clutch is brand new.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 180 Answers

Hello
A new clucth will slip a little at first. Its recommended to try to make the clucthes slip.
i just put in a set that instructed me to make the clutches slip.
A brand new set of clutches needs to seat and it will take a few times riding it before it does.

If they continue to slips after a few rides then you should have your master cylinder bled.
If the clutches are not engaging all the way, the clucthes will slip and motor revs but bike dont move.
if the clucthes are not disengaging all the way, the clutches drag, and the bike will edge forward because the clucthes are not disengaing from the motor.

Thats a pretty simple set up, hydraulic just needs to be bled all the way in the same manner you bleed a brake caliper.
once bled there is no adjustment and the clutches should disengage and engage within the first 1/2 inch of pulling in the lever.

Hope that helps, and don't worry about your new clucthes, they will slipp a little but will go away.
i'm sure of it.
Best Regards
Big Al

Posted on May 22, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Intruder 1400VS Iam getting delayed acceleration -almost a winding up when engaging throttle


possibly clutch slip , does it rev up higher but theres a delay in the bike speed matching the revs ?

Jul 25, 2014 | 1994 Suzuki VS 1400 Intruder

2 Answers

Not Accelerating beyond 40-50 kmph


NOT clutch issue - if it was the clutch the rpms would rev out but bike would go no faster.
Sounds like carburetor may be partially plugged up, main jet.
Or air filter needs replacing.

Apr 03, 2014 | 2006 Bajaj Wind 125

1 Answer

Engine revs but nothing happens


Replace the clutch plates or adjust the clutch cable. Try the clutch cable first. What you have is a slipping clutch. It could be that the clutch cable is too tight and so the plates aren't mating fully when you release the lever, or it could be that the plates are worn out. But as it is getting worse it is most likely to be the clutch plates are worn.

Sep 10, 2013 | 1991 Yamaha FZR 600

1 Answer

Engine revs up and down when airconditioning is on


The ac compressor takes around 5 hp to drive so when the clutch engages the idle speed will drop around 250rpm amd when the clutch dis-engages the rpm will rise 250 rpm If you have a efi computer controlled vehicle the computer should automatically adjust the rev difference to maintain a constant rpm. If you have a carby vehicle there is a electric over vacuum control that you can fit to the accelerator lever that when the clutch activates the power to the switch from the clutch opens a valve that allows vacuum to pull the throttle open and maintain a constant rpm

Aug 01, 2013 | Air Conditioning and Heat for Pontiac G6

1 Answer

Speed Triple fell at about 10 MPH on the right side and slightly bent the throttle handle bar at the tip. Its still driveable, but as i increase the throttle in any gear, it revs high but speed does not...


Put the bike up on blocks to roll wheels freely in neutral. do they turn freely? If not, check for stuck brakes, maybe rotors or pads. Then remove the plugs, clutch lever released, put in in a high gear and roll it around to see if this is rotating your pistons up and down. This tests clutch slippage. if you can roll the bike around. You pull the plugs so that the engine compression does not lock up the rear wheel. An engine that revs up like that and does not speed up the bike is usually either a sticking brake or a slipping clutch. Let me know what you find, and we'll narrow this down so you can get it fixed.

Dec 10, 2010 | 2007 Triumph Speed triple

1 Answer

Escort 1 6 zetec engine revs high when stationary and tries to run away when driving. Have checked the throttle linkage, and all is moving as it should be. If the throttle is blipped it acts as if it has...


i think the problem is the idle\air control module if you have one take it out and clean it. the idle module works when your vehicle is idleing. A clogged throttle body or intake would cause the module to compensate for the problem by allowing air in and around the throttle body bypassing it. so i think some thing in the intake system is clogged.

Apr 18, 2009 | 1997 Ford Escort

Not finding what you are looking for?
2007 Suzuki Boulevard C50 Logo

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...