Question about 2005 Harley Davidson FLHR - FLHRI Road King

1 Answer

When i turn on my switch and hit my start/run switch it will not turn over and it do have all the power on

Posted by on

  • london_rober May 26, 2011

    it was very helpful and thank you.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Master
  • 5,370 Answers

It can be the problem with start switch or there is loose wiring to the start run or switches.It has to be checked.There are many other possibilities to be checked to confirm the fault.Click this link below and follow the troubleshooting:--- -------------- This should help.Thanks.Helpmech.

Posted on May 22, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Why does it fire when the key is shut off

Ignition switch,bad fusible links, coil,ignition module. I have replaced several switches for this problem. At the coil, when you turn the switch on, there should be power. There also should be power when trying to start the engine. If there is no power while cranking, replace the switch. The reason it hits a cylinder or two is that the power goes to the coil, just not enough to get the engine running..

Aug 08, 2014 | 1981 Chevrolet Corvette

1 Answer

2003 suzuki volusia has power but when hit start goes dead

short in ignition switch- common in these bikes.. check it carefully

Jul 13, 2014 | 2003 Suzuki VL 800 Volusia

1 Answer

How may belts on lg tromm dryer

The start button is a momentary start button. It energizes a relay type switch to keep power on. Try holding the start button in for awhile and do not let go. If the machine keeps running, then for sure, the relay type switch is defective and needs to be replaced with a new one.

May 24, 2014 | LG TROMM WM2688H 4.0 cu.ft. Front Loading...

1 Answer

Dryer won't start when start button is pressed

does outlet have power? if yes check DOOR SWITCH look on door for door switch lever then on dryer were it will hit switch. you can try to press it with a screwdriver or something while turning on sryer start. also you can bypass the switch by taping the wires together and see if it then works. switches are cheap.

Jan 25, 2014 | Maytag PYE2300AY Electric Dryer

1 Answer

How to calibrate speed on a treadmill

Make sure power switch is off; hold down any key on the display and turn power switch back on. Unit will go into diagnostic mode. Press and hold the start key until unit beeps and begins to calibrate. Make sure you are not standing on the belt during process. Let unit run its course and slow completely then hit stop. you're done.

Dec 30, 2013 | Cybex 530T Pro Plus Treadmill

1 Answer


Sounds like you have linked these up to ignition switch out feed to the kill switch/running curcuit rather than the lighting curcuit out from the ignition. most bike run 2 somtimes 3 curcuits out from the ignition switch one running curcuit and one lighting.

Feb 21, 2012 | 2007 kawasaki Vulcan 1600 Nomad

1 Answer

2006 fxdi I can turn on the key and run switch the bike runs it diagnostic check and as soon as I hit the start switch I lose all power. The bike has a new battery and was just serviced.

Ring the service center and hit them up with your problem. It sounds like the computer is either swithching everything off because there is a greater problem that it is protecting.

May 25, 2010 | 2006 Harley Davidson FXDI Dyna Super Glide

1 Answer

Pover up trouble

sounds like something is drawing down on your 12 volt supply drives or on board regulators. Try it without the drives connectged, and see if you can get the system to boot up(you'll just get a notice that your drives are unavailable, but you'll already know that, right?

got backup for your Dell?

Feb 15, 2008 | Dell Dimension 5100 (D51L1) PC Desktop

Not finding what you are looking for?
2005 Harley Davidson FLHR - FLHRI Road King Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

4340 Answers


Level 3 Expert

76691 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides