Question about 2011 Suzuki TU250

1 Answer

Where do i fill brake fluid on my 2011 suzuki tu250? I disassembled everything from the bars and when I put them back on and everything back together, everything worked except the front brake has no pressure. We bleed the brake line, but even after working the brake lever and bleeding several times, we never got any pressure and the front brakes are not engaging at all.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 66 Answers

Attached to the front brake handel is a black box type reservoir with two screws in it. Make sure the reservoir is level remove the screws and the cover then inside is a rubber boot and plastic piece make sure they go in the same way they came out. Except the rubber piece will be collapsed into its self when the oil is replaced. Fill the reservoir with DOT4 brake fluid and re bleed the front brakes to be sure you got all the air out of the system. you do not have to replace the cover to bleed the brakes just be careful not to get any brake fluid on the painted surfaces of the bike it is not good for the paint.

Posted on May 21, 2011

Testimonial: "This was amazing. The answer came back much much faster than I expected. The response was easy to understand and instructions were easy to follow."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

All information on Suzuki Grass Tracker 2002 in totally original condition. 250cc


Hi, Robbie the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee around $10 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download for viewing or printing. To download your manual please click on the blue links below. Good luck and have a wonderful day
TU250 Suzuki Motorcycle Online Service Manual Cyclepedia $27
OEM parts for Suzuki
http://mybikemanuals.com/suzuki
Suzuki Grasstracker BigBoy 2002
Suzuki TU250 Wikipedia

Oct 01, 2017 | 2005 Suzuki Grasstracker

2 Answers

Rear brake is sticking on 88 bronco 2.4x4.how can i fix it


I usually disassemble the brakes and lube the shaft. Then stick it back together putting the spring tension on 3.

Sep 22, 2014 | Avid Shorty 6 Cantilever Brakes Rear

1 Answer

I replaced rear wheel barrings on my 2004 crf 450. I disonnected brake line when doin this. i then put everything bck together and bled brakes got air out. rode bike tested out n brakes didn't work. so...


U didn't have to disconnect the brake line to take wheel of but anyway make sure the brake line fittings are tight and make sure u put the the copper washer back on the fitting then bleed the brakes again by filling pumping then undoing bleeder a little then keep repeating till the brakes reel hard and make sure the brake pads are moving.

Jun 20, 2013 | Cars & Trucks

1 Answer

Handelbar wiring streetglide


changed the switch housing when after putting back together i have no turn signels, no brakes lights, no horn, or no criuse control light, everything else works fine, what could be the problem? Before putting everything back together everything worked but it was after the job was done that it didnt work

Feb 05, 2012 | 2009 Harley Davidson FLHX Street Glide

2 Answers

Rear brakes don't work on my 2004 Sportster


Air in system push caliper piston right in & hold while bleeding

Ride Safe

Bike-Doc

Jan 22, 2012 | 2004 Harley Davidson XL 883C Sportster...

1 Answer

I was changing the front disc brake pads on my 2008 Suzuki Boulevard S50. I took the two bolts out that hold the calipers together which caused the fluid to leak out and a small rubber gasket fell out ....


You will need to buy a new rubber gasket kit for caliper from suzuki shop
It is not usual to pull caliper apart for pad replacement, normally unbolt caliper off fork leg and lift of the disk

Jul 08, 2011 | 2008 Suzuki Boulevard

2 Answers

My rear brakes stick and will not release on my 03 gsxr, I pulled the caliber off and the pistons compressed right back in. So that leaves me to wonder what kind of problem as I looking at?


Most likely the master cylinder bypass valve is stuck you would have to replace the master cylinder to fix this problem. However to test it for this problem apply the brakes with everything together next open the bleed valve without stepping on the brake, does fluid shoot out of the bleed valve? if yes then you master cylinder is defective. If it is cable operated then pull the clevis off the brake and see if the cable moves smoothly and does not stick, if it sticks replace the whole cable assembly. If you still need help just reply to this post and thanks for using fix-ya.

Jun 01, 2010 | 2003 Suzuki GSX-R 600

2 Answers

Changing the clutch fluid in my 91 gixxer 1100. How do I bleed the clutch


daea339.jpg note: use an neoprene tube that fits on the clutch bleeder screw an a glass jar with other end of tube coverd in brake fluid so not to let air get back in system

Pump / release clutch slowly for not to spill out of res while bleeding/ flushing old fluid out

Keep the res full so not to let air in system by adding fresh fluid

Mar 31, 2009 | 1989 Suzuki GSX 550 EF

Not finding what you are looking for?
2011 Suzuki TU250 Logo

300 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...