Question about kawasaki VN 1500 Vulcan Classic Motorcycles

1 Answer

Just replaced the friction plates, the clutch spring hub does not seat onto the splines. What did i do wrong?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 167 Answers

G'day.
You don't stipulate your bikes model or year which makes this a bit harder.
When you fitted the outer hub(the one the springs sit in)- you've probably miss-aligned it.
Remove the springs again
Remove the hub- & re-fit over next set of posts(turn the outer hub so it dosn't go over the same posts as before) & it should slot all the way in.
If it dosn't-try again

It looks like the outer hub can fit over the spring posts in any position- but it can't.

I hope this works for you.

Regards Andrew Porrelli

Posted on May 21, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can pressure plate vibrate a car


Hi in most situations the pressure plate creates this kind of fault. Examine the clutch plate for premature failure. EG: WORN spline hub, damper springs,friction material damaged.IN some case experiences the flyweel developed hard sports (burnt marks) or flyweel surface not running through when tested with a dial gauge.

Apr 24, 2016 | Cars & Trucks

1 Answer

HOW DO I CHANGE MY CLUTCH AND PLATES 2008 FLHTCU?


Clutch and plates replacement can be performed on the motorcycle without removing the clutch shell or hub.


FIRST remove the primary chaincase cover. THEN remove six metric bolts to release the clutch diaphragm spring retainer from the clutch hub by loosening each bolt gradually and in a star sequence around the Hub circumference and then remove the diaphragm spring retainer, the diaphragm spring and pressure plate from the clutch hub and after the pressure plate has been removed remove the 9 friction plates, the steel plates, the damper spring and the damper spring seat from the clutch hub. Clean and inspect as necessary and wash all parts except for friction plates (and any bearing if removed) in appropriate cleaning solvent and then blow parts dry with low pressure compressed air as high pressure compressed air is unnecessary and dangerous. CHECK the friction plates by blowing off all lubricant from them BUT DO NOT wipe them off with a rag if they are going to be reused. THEN measure the thickness of each plate with a dial caliper or micrometer and if any plate is less than 0.143 in. (3.62 mm) thick throw them all away and replace them with a complete new set. ALSO look for worn or damaged fiber surface material on all sides. If new friction plates will be installed soak them all in FORMULA+ TRANSMISSION AND PRIMARY CHAINCASE LUBRICANT (or whatever equivalent oil that you will be using in the primary after reassembly) for at least five minutes. THEN CHECK the steel plates for any grooving, bluish colouring (which indicates overheating/burning and which is usually accompanied with distortion/warping) and check for distortion by laying each plate on a machinist or other precision flat surface and try to insert a 0.006 inch (0.15 mm) feeler gauge between the plate and the precision surface. Do this in several places around the plate. If the feeler gauge slips under any plate or any plate is grooved, bluish or otherwise appears to be defective discard it and replace with a new plate. THEN rotate the clutch hub and shell to check for bearing smoothness and replace the bearing if it runs roughly, binds or has any end play. ALSO check the primary chain sprocket and the starter ring gear on the clutch shell at this time and replace the clutch shell if either the sprocket or ring gear are badly worn or damaged. ALSO check the slots that mate with the clutch plates on both the clutch shell and the hub and replace the shell or hub if any of the slots are worn or damaged (wear here can cause clutch hang-up on release). NOW check the diaphragm spring and diaphragm spring retainer for cracks or bent tabs and replace if any damage is evident.


After having soaked the friction plates as advised above first install the narrow friction plate on the clutch hub, engaging the tabs on this plate with the slots in the clutch shell then install the damper spring seat (sometimes called a judder spring) on the clutch hub so that it sits inboard of the previously installed narrow friction plate with the concave side out (facing away from damper spring

seat) (that will be with the narrow side facing into the clutch hub and the wider side facing out) THEN install a steel plate with the round edge (produced when the plate was stamped out from a larger piece of steel) outward and then install a regular friction plate onto the clutch hub and continue by installing the seven remaining sets of steel and fibre plates in the same manner, alternating between steel plates and friction plates so that no two steel are touching each other and so that no two fibre plates are touching each other and then when they are all in place install the pressure plate onto the clutch hub aligning holes in the plate with the threaded bosses on the hub. THEN install and seat the diaphragm spring into the recess of the pressure plate with the concave side inward and with the holes in the diaphragm spring retainer aligned with the threaded bosses on the clutch hub tabs on the spring retainer contact flats on the inboard side of the bosses install the six metric bolts to secure the diaphragm spring retainer to the clutch hub and alternately tighten the bolts to 90-110 in-lbs (10.2-12.4 Nm). THEN install the primary chaincase cover with a new gasket and torque the fasteners to 108-120 in-lbs (12.2-13.6 Nm) in a sequence top to bottom from the centre to the front and then top to bottom from the centre to the back of the cover and then reinstall the primary case drain plug and o-ring and torque it to 14-21 ft-lbs (19.0-28.5 Nm). THEN refill the primary chaincase with lubricant only up to the bottom of the clutch diaphragm spring (if there is too much oil the clutch may drag). THEN adjust the clutch by turning the clutch adjustment screw in until it just resists and then with the cable slack somewhat removed operate the clutch lever a few times to set the clutch release balls in their ramps and then recheck the clutch release pushrod adjustment screw again so that it just resists tightening as it is screwed in and then back it out one half to one full turn and while holding it stationary tighten the adjuster screw lock nut. THEN the cable can be adjusted to provide one sixteenth to one eighth of an inch of freeplay at the clutch cable bracket or perch on the handlebars. THEN reinstall the clutch inspection (derby) cover with the five T-27 Torx screws and washers and alternatively in a cross pattern tighten the screws to 84- 108 in-lbs (9.5-12.2 Nm).

Jun 19, 2014 | 2006 Harley Davidson FLHRI Road King

1 Answer

2006 harley clutch pack assembly


After having soaked the friction plates as required first install the narrow friction plate on the clutch hub, engaging the tabs on this plate with the slots in the clutch shell then install the damper spring seat (sometimes called a judder spring) on the clutch hub so that it sits inboard of the previously installed narrow friction plate with the concave side out (facing away from damper spring
seat) (that will be with the narrow side facing into the clutch hub and the wider side facing out) THEN install a steel plate with the round edge (produced when the plate was stamped out from a larger piece of steel) outward and then install a regular friction plate onto the clutch hub and continue by installing the seven remaining sets of steel and fibre plates in the same manner, alternating between steel plates and friction plates so that no two steel are touching each other and so that no two fibre plates are touching each other and then when they are all in place install the pressure plate onto the clutch hub aligning holes in the plate with the threaded bosses on the hub. THEN install and seat the diaphragm spring into the recess of the pressure plate with the concave side inward and with the holes in the diaphragm spring retainer aligned with the threaded bosses on the clutch hub tabs on the spring retainer contact flats on the inboard side of the bosses install the six metric bolts to secure the diaphragm spring retainer to the clutch hub and alternately tighten the bolts to 90-110 in-lbs (10.2-12.4 Nm).

Apr 16, 2014 | 2006 Harley Davidson FXDI Dyna Super Glide

2 Answers

Clutch removal and reassembly


last time i changed that part i went to U-tube and found a video someone posted and watched it for an easy solution

Jun 04, 2012 | 2004 Mitsubishi Outlander

1 Answer

I need to know how to remove lutch from kawasaki 65


1- Remove nuts, clutch spring plate and springs 2 Feed a rolled-up rag between both primary reduction gears to prevent the clutch from turning, then remove the clutch hub nut. 3- Remove clutch hub, pressure plate, steel plates and friction plates. 4- Remove clutch housing. 5- Slide clutch bushing and thrust water from shaft. Take care to note how thrust washer is installed.

Sep 24, 2011 | 2003 kawasaki KX 125

1 Answer

1998 ford contour 2.5 ltr manual,stuck in second and have to hold the clutch in to move it.how do i solve this issue?


SECTION 308-00: Manual Transmission/Transaxle and Clutch - General Information 1998 Contour/Mystique Workshop Manual DESCRIPTION AND OPERATION Manual Transaxle and Clutch Manual Transaxle and Clutch - General Information This section covers general procedures for diagnosis and testing the clutch system. For additional information, refer to Section 308-01 . For specified clutch system service procedures. For additional information, refer to Section 308-02 . For a complete description of the manual transaxle. For additional information, refer to Section 308-03 .
The clutch system includes:
  • Flywheel.
  • Clutch disc.
  • Clutch pressure plate.
  • Clutch master cylinder.
  • Clutch slave cylinder.
  • Clutch release fork.
  • Clutch release hub and bearing.
The clutch master cylinder transmits fluid pressure to the slave cylinder, which in turn moves the clutch release fork and the clutch release hub and bearing.
The clutch master cylinder uses brake fluid and shares a common reservoir with the brake master cylinder
The clutch is a single plate, dry-friction disc with a diaphragm-style spring clutch pressure plate. The clutch disc has a hub which is splined to the input shaft. The clutch disc has friction material where it contacts the flywheel and the clutch pressure plate. Torsion springs on the clutch disc help absorb the engine torque pulses. The clutch pressure plate applies pressure to the clutch disc, holding it tightly against the surface of the flywheel.
In the engaged position, the diaphragm spring holds the clutch pressure plate against the clutch disc, so that engine torque is transmitted to the input shaft. When the clutch pedal is depressed, the clutch release hub and bearing pushes the diaphragm spring center toward the flywheel. The diaphragm spring pivots at the fulcrum, relieving the load on the clutch pressure plate. Steel spring straps riveted to the clutch pressure plate cover pull the clutch pressure plate from the clutch disc, disengaging the engine torque from the transaxle and enabling the gears to be changed.
-----------------------------------------------------------------------------------------------------
Inspection and Verification - MTX-75
The following checks should be carried out before repairing or replacing the transaxle:
Poor gear shifting
  1. Check the operation of the clutch: Lay a block of wood approx. 25 mm thick under the clutch pedal and depress the clutch pedal as far as the stop. If 1st or 2nd gear can be selected with no problem with the engine running and the parking brake applied, the clutch is OK. If the gear cannot be selected, repair the clutch.
  1. Check the selector mechanism:
    • The free play in the gearshift lever must be no more than 15 mm.
      • If the gearshift lever free play is too great, check the gearshift cables and replace them if necessary.
    • If the gearshift lever free play is OK, adjust the gearshift linkage. For additional information, refer to Section 308-06 .
  1. Check the transaxle fluid level and top up with Automatic Transmission Fluid ESD-M2C186-A if necessary.
--------------------------------------------------------------------------------------------------------------------------------------

Dec 21, 2010 | 1998 Ford Contour

1 Answer

My clutch wont work


http://www.bikebandit.com/2002-ktm-motorcycle-125-sx/o/m4758#sch465207

Please see this schematic to understand your clutch.
There are springs which press two SETS of many plates together. One set is metal disk construction and splines into the inner hub of the clutch basket assembly. The other set is made up of metal, with (often) compressed cork material - these spline into the outer hub. When the lever is pulled in, the spring pressure is relieved off the plates, and the inner and outer hub are independent of each other. When released, the springs push the plates together, locking the inner hub(engine power) to outer hub(transmission) Now that you understand how it works, I'd say the solution is clear, open up the clutch and take a look at your plates.

Dec 01, 2010 | 2002 KTM SX 125

1 Answer

How do i know i need a new clutch and clutch basket in my 2002 cr 125


Clutch friction plates are often the worn out component of that assembly. IF the plates don't spline in correctly with the basket due to some physical damage, then you should replace the basket. The clutch is comprised of an inner and outer hub that become interlocked through metal disks and friction disks pressed together under spring pressure.

http://www.bikebandit.com/houseofmotorcycles/2002-honda-motorcycle-cr125r/o/m2178#sch304800

Follow this link to a schematic of your 2002 honda cr125 to see how it all fits together.

Nov 28, 2010 | 2002 Honda CR 125 R

1 Answer

Clutch locked up on my 82 Suzuki dr250 I am at a loss what should I do.


your clutch is simply a stack of friction disks and metal plates. The friction disks are splined into the outer hub ring and alternate, one friction disk / one plate / one friction disk / one plate etc. It's very simple to free this up if it's locked up. remove clutch cover. If you are unsure which is your clutch cover, follow the clutch lever cable to the actuator arm. remove the cable from arm and all bolts holding the cover. as you pull out the cover, you will see the arm rotate that's because it's geared into an arm that is connected to the front plate of the clutch basket assembly. You'll see it as soon as you pull it off. now you'll be looking at a round plate with 6 bolts with springs underneath. when you arent pulling the lever, these springs are extended and push the friction disks and metal plates together, thereby locking the inner hub to the outer hub. The inner hub is connected to the crank, and the outer hub is connected to the transmission input gear. So, if pressed together by the springs, your engine running causes your bike to move. Pulling the clutch lever in pulls the spring tension off the plates and allows them to separate. This allows your engine to be disconnected from the transmission. If your plates are locked together you will remove them one by one if you can and lubricate between each plate and disk and reinstalling. Pay close attention to how it came apart. Reinstall bolts and springs reinstall cover, aligning the lever gear teeth with the front of the clutches teeth correctly. put it all together and see if you are okay now.

Nov 23, 2010 | 1988 Suzuki Rg 250

1 Answer

How many clutch plates are inside A 1990 suzuki dr650s




Reading from my manual (Suzuki Service Manual)

Primary drive gear (the clutch "basket")
Spacer
Clutch pressure plate
Clutch drive plate (has friction pads) x 6 of these alternating with...
Clutch driven plate (smooth) x 6 of these
Clutch drive plate (thicker with friction pads) x 1 of these to finish plates
Wave washer
Wave washer seat
Clutch sleeve hub then goes on with springs etc.

please check the site below, it has exploded views of the bike in all categories.

Cheers.

http://www.cmsnl.com/suzuki-dr650-s-1990-1991-usa_model15961/partslist/

May 09, 2010 | 1990 Suzuki DR 650 RS

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75077 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...