Question about Honda Cb 400 Super Four Motorcycles

1 Answer

What kind of oil do i put in and how much in each tube?

Posted by on

  • enzo_67_842 May 19, 2011

    honda cb 400 super four version s/im asking about fork oil

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

What sort of motorcycle is it? And are you asking about fork oil or engine oil, as the two are very different.

Posted on May 18, 2011

  • enzo_67_842 May 19, 2011

    i have a honda cb 400 super four version s,and im asking for fork oil

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What kind of gear case oil for 1972 4hp evinrude


EP 80-90 will do.Buy a small squeeze tub of gear case oil at most walmarts, etc. After draining, remove both upper and lower plugs, best if using a squeeze tube because you want to fill from the bottom up. Put the tube tightly in the bottom port and squeeze until it comes out the top. Put in the top plus so it will not come right out the bottom port. Quickly remove the tube and put in the bottom plug and tighten. Remove the top plug and top off as necessary. This process ensures no air is trapped in the gear case. It takes longer to type this than it does to do it.

Jul 15, 2014 | Boating

1 Answer

Yamaha 650 how change fricction plates and put it back all together included springs


Be carefull to avoid friction reducing oils or any kind, this bike was built well before synthentics so don't think you "must" use the full synthentic oils. Mobile 1 15-50 is an excellent oil, replace the filter while performing maintenance on the plates, you will need 3 quarts of oil. To change the friction plates watch the video some guy made on you tube.

Mar 16, 2013 | 1982 Yamaha XJ 650

1 Answer

What kind of oil do i put in my truck


It should be indicated on the oil filler cap on the oil filler tube. I would check with an auto parts store where you buy motor oil.

I did a Google search and 99% say 5W 30. I have a Dodge Nitro and use 5W 30. Most new engines are designed to uses lighter oils for better starting during cold conditions.
Jim

Dec 19, 2011 | 2002 Dodge Durango

1 Answer

What kind of oil do I put in?


They sell tubes of oil for the saws. If you can't find it You can probably use 90weight gear oil. the stuff in the tube smells about the same.

Sep 05, 2011 | Skil Circular Saw 7 14" HD77 Worm Drive

1 Answer

What kind of oil do i put in my skill saw 77


This saw requires Skil's heavy-duty, worm-drive oil, part number 80111. If you can find a local vendor that has some great otherwise, type 'skil 8011' in your search engine and shop around for an 8oz tube, they can run from $5 to $10 plus shipping.

Jan 28, 2011 | Skil 7 1/4" Magnesium "Mag 77" Wormdrive...

1 Answer

How do I reassemble front forks of bike


Refer to this site, www.bikebandit.com for an exploded view of the front forks. Basically you must have the seals in the slider (lower part) and the damper tube in the upper fork tube. Then slide the upper fork tube down into the lower and install the bolt in very end of the slider. Then install the spring and top plug or put it in the triple trees and intstall the top cap. You'll have to put the appropiate amount of the correct weight oil in the tubes. The amount depends on what kind of forks they are. Since they've been taken apart, use the "dry" (as compared to 'wet") amount of oil.

Good Luck
Steve

Oct 27, 2010 | 2000 Harley Davidson FXST Softail Standard

1 Answer

Snapper 25 hp (kohler engine) mower


When checking the oil donot put dip stick clear in just let it set on top then pullit to check oil.rreplace it and tighten. Your putting to much oil in it.

Apr 30, 2010 | Ford Tractor 8n Front Emblem

1 Answer

Oil in rear projection t.v.


The "oil" is actually tube coolantthat is supposed to be between the lens and the tube. If the coolant was low you may have damaged the tube and maybe melted the lens if happened to be plastic.

Jun 26, 2009 | Toshiba 43A10 43" Rear Projection...

1 Answer

Magnavox 60'' rear projection screen tv


That oil is glycol and is a coolant for the tube. Hope you didn't get the oil on the circuits because it is conductive and the tv will not operate with the oil on it. Must be completely full. Can be bought a electronic parts distributors or a tv shop could order you a bottle. Hope you just removed one tube only. Make sure you seal it back good

Dec 30, 2007 | Philips Magnavox 9P6034C 60" Rear...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77202 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...