Code p305 cylinder misfire 02 mazda mpv 3.0 changed coil , clean injector ,checked compression ok code still appears. was reading on line forum they said i have a bad EGR valve please advise

If you're still experiencing a cylinder 2 misfire in your 2013 Dodge Avenger 3.6L V6 after replacing the coils, spark plugs, and wires, there are a few potential causes to consider: 1. Fuel Injector Issue: A malfunctioning or clogged fuel injector can cause a misfire in a specific cylinder. Check the fuel injector for cylinder 2 and ensure it is functioning properly. It may require cleaning or replacement. 2. Compression Problem: Low compression in cylinder 2 can lead to a misfire. Perform a compression test to check the compression levels in all cylinders. If cylinder 2 shows significantly lower compression, it may indicate issues with the valves, piston rings, or cylinder head gasket. 3. Ignition Timing: Incorrect ignition timing can cause misfires. Ensure the ignition timing is set correctly according to the manufacturer's specifications. 4. Vacuum Leak: A vacuum leak near cylinder 2 can disrupt the air-fuel mixture and lead to a misfire. Inspect the vacuum lines and intake manifold for any leaks or loose connections. 5.Engine Control Module (ECM) Issue: A faulty ECM can incorrectly trigger a misfire code. Consider having the ECM scanned for any error codes or anomalies related to cylinder 2.

Possible causes
- Faulty spark plug 5
- Clogged or faulty fuel injector 5
- Faulty ignition coil 5
- Fuel injector 5 harness is open or shorted
- Fuel injector 5 circuit poor electrical connection
- Ignition coil 5 harness is open or shorted
- Ignition coil 5 circuit poor electrical connection
- Insufficient cylinder 5 compression
- Incorrect fuel pressure
- Intake air leak
What does this mean? What does this mean?
Tech notes
The P0305 code means that the cylinder 5 is misfiring or is randomly misfiring. Start by checking for intake leaks an if no leaks are found the next step is to replace the spark plugs on cylinder 5. If the problem persist more tests needs to be done to diagnose problem, see "Possible Causes"
What does this mean? What does this mean?
When is the code detected?
Engine Cylinder 5 is Misfiring.
Possible symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/loss of power
- Hard start
- Engine hesitation
P0305 Jaguar Description

When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the Crankshaft Position (CKP) sensor signal to vary, the Engine Control Module (ECM) can determine that a misfire is occurring.

Read more:
P0305 Jaguar Cylinder 5 Misfire Detected

misfires can be from electrics( HT leads -plugs -coil/s ) and also be from injectors ( low fuel pressure --dirty injectors -pulse problems --electronic). Run the codes to find if it is a random problem or a specific cylinder misfiring to point you in the right direction.

You have an interference motor. If you had to replace the heads due to the valves possibly touching the motor, you have to consider rechecking the compression after you replaced the heads. I had the same motor that had an intake leak. I found frozen rings on the number 1 piston as well as a bent pushrod. Ultimately, the camshaft had broken due to coolant getting to the bearings. If the spark is good, the fuel is good, then the only other problem you'd have would be compression.

If you changed the #5 Coil then the code was wrong

You get lots of wrong codes on a ford, as a bad coil
spikes the pcm when grounding out to fire the coils
secondary side

Try putting the old coil back & walking the new one to
another cylinder,may take many days & many miles of
driving to get it fix,but better than a shop guessing, because
they hate fords

I answered this already

If a MIL Lamp is flashing please do not use the car

That on a ford that is called a Class A Cylinder misfire & will
destroy your exhaust converter, as well as possible other
engine damage,work on the misfire issues

was the any oil on the coil boot? you can have a weak injector or a stuck vavle

I'd check #1 spark plug.
Usually a misfire code "fix" is a spark plug, spark plug wire, or a coil pack / distributor.
Keeping it simple...I'd go with the spark plug first and then look at the condition of the wires.

Hope this helps...

no the bad oxygen sensor never affects misfire it affects only the air/fuel mixture
those are causing misfire (a bad coil, ignition module, distributor pickup, crank sensor,).
and i doubt the crank sensor cuz computer says sensor even if it said to be o2 but no its the crank one its ok if computer fault
i hope my answer was useful

please check on compression of all the cylinders. IF there is any valve damage this could cause a fault.Please check this out if your fuel and spark are ok.