Question about 2003 Yamaha YZ 125

1 Answer

How do I replace the kick start assy? - 2003 Yamaha YZ 125

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Yamaha Master
  • 41,764 Answers

Hi, Cows_go_moo for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Broken kickstarter shaft help Yamaha 2 Stroke
YZ125 Tear Down Part 4 Removing 2 stroke Kickstarter side case and water...
YAMAHA YZ125 Owner Service Manual
OEM parts for Yamaha

Posted on Jul 19, 2016


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 2005 RMZ 450. The rod on the crank shaft blew apart and i had to replace both cases, crank, piston and rings, get the cylinder fixed and plated. I had a local Suzuki shop replace everything. ...

Sounds like your ratchet gear is mis aligned, when you put the ratchet gear together it has alignment marks that have to line up when you insert it back in the case...The kick shaft being bent slightly should not prevent the engine from turning over. I hope this helps.

Jul 21, 2011 | Suzuki RM-Z 450 Motorcycles

1 Answer

My 372xp was in use and started reving up at full rpms and wont kick down. What could i do ?

check idle settings, if its ok check all valves and carburator assy is ok, check gaskets and sealings.

Mar 25, 2011 | Husqvarna Chain Saw Models 371, 372xp

1 Answer

Karcher 3.98M Switches On and Off after Releasing Trigger

Yea the pressure cleaner has a internal water leak it thinks you are trying to turn it on then kicks in and realises that you are not...
on these cheap units sometimes it is not worth fixing if you still have good pressure... other wise you could take it to a tech and get the plastic head and valve assy replaced that will most likely fix it very common problem....


Sep 06, 2009 | Karcher K2.26 Electric Power Washer

1 Answer

Fuel pump not activating

Sorry you got the task of replacing a heater core. But never the less there is a fuel cut out /roll over switch located in the passenger kick panel and the harness runs up thru the dash. Two things could have happened.
1-the fuel cut out triped. Reset by pulling the passenger side kick panel and reset by pushing the red or yellow reset button. This should cure the problem.
2-the harness to the cutout switch was disconnected while working under the dash or pinched while the installing the blower assy. you can take a DVOM and check the resistance at the switch harness while disconnected from the switch. If the meter reads less than .003 you have a short. If not while disconnected check the switch by depressing the button and check across the terminals. The meter should have an audiable mode and listen for a beep. This means the switch is good. If no noise replace the switch.
Good Luck.

Jan 26, 2009 | 2002 Ford Crown Victoria

1 Answer

Stripped start knob

That would be the timer assy You may need to replace entire assy and knob you could try a strong 2 part epoxy and allow to dry min 24 hrs at room temp.

Dec 11, 2008 | GE DCSR483EA Electric Dryer

2 Answers

Furnace won't kick on

Downstream of your fan discharge there is a little plastic assy. most likely that will have a pickup tube and a piece of vinyl or latex tubing attached. First check to make sure that the pick up tube and/or tubing does not have a restriction. If it is clean use an ohm meter to read resistance across the switch to verify it is operating.

Nov 15, 2008 | Intertherm Heating & Cooling

1 Answer

Kick Starter

THis is pretty vague but most of these require taking the bolt out completely to slide in on the shaft . then put bolt thru assy and tighten

Jul 25, 2008 | Yamaha RX-V800 Receiver

1 Answer

New start button?

Hello Colette,
When a component sometimes works and sometimes doesn't work, it suggests the component itself is functioning correctly. Check for loose wire connections on the door switch, the start switch, and on the cycle-reset switch which is located on the cam-timer assy of the machine (if so equipped). Cam timer assy is behind the kick-plate, under the door.

Jun 25, 2008 | Jackson 24 in. JPX-300H Built-in...

2 Answers

My Whirlpool Fridg. Model ED22RF has a problem. The freezer is defrosting and neither side is cold. Sounds like the compressor switch is kicking on for a second and then off but the compressor never really...

yea that sounds like a compressor issue( under 5 year manufactrue warr.) you can try replacing te overload/relay assy mounted to the side of thecompressor , sometimes you get lucky and it works part number 4387767

Mar 26, 2008 | Refrigerators

Not finding what you are looking for?
2003 Yamaha YZ 125 Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts


Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers


Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides